Metronic AccessBox, Руководство пользователя

Страница: 2 / 24

1
CAUTION
Your AccessBox has ventilation slots. These slots must not be obstructed, even partially, in order to
ensure proper ventilation. The lifetime and normal functioning of your device depends on these factors.
The
device may not be exposed to dripping or splashing and no object filled with liquid, such as vases, must
be put on the device.
Installation in premises which are confined or subject to temperature or dampness
changes (sheds, attics, cellars, tiny rooms, dry risers etc.) may cause an overheating of the device or a pre-
mature ageing resulting in failures that are not covered by the guarantee.
Never open the Access box receiver even when it is not connected, because it contains electrical com-
ponents, which can be dangerous for you. In general, electrical appliances are not earthed, so you can get
electrical discharges (which are not risky), while implementing the connections. Our advice is to connect
the equipment after all the sockets connections have been made.
To clean the receiver or his remote control, do not use any solvent or detergent. Use only a dry cloth
for dust or slightly dampened with water for the front panel. Always carry out this operation after having dis-
connected the receiver from the mains.
For your own safety:
Never open the device. It contains no item that can be serviced by the user. If you open it, make some
changes on circuits or connections of non-compliant equipment it will cancel the guarantee. If necessary,
please return the receiver, for service, only to the point of sale.
In order to reduce the risks of fire, electrocution or damage caused to another equipment or someo-
ne, do not expose the device to dampness, bad weather, dust, sand, sun, cold or high temperature. You must
use the device between 0°C to 40°C; 32°F to 104°F. Place your AccessBOX in a dry place, safe from dust.
It is not designed for outdoor use.
The remote control needs two AA 1.5V batteries. Check the polarity before fitting them into the remo-
te control. Do not throw your used battery in the bin, take them to your local store where special boxes are
provided to recycle them.
The installation and the use of the receiver are based on pre-programmed channels. In the event of
problem on a channel, get a specialised magazine to find out if this channel is still broadcasting in Free To
Air. For information, the operators frequently change the channel’s characteristics without notice.
Your receiver is compatible with DiSEqC 1.2, it could be used then with a DiSEqC 1.2 motor (or rota-
tor). In case of a DiSEqC 1.2 motorised installation, our advice is to install the motor in an easily accessible
location (avoid chimneys, for example). Motors may have to be screwed up or lubricated. An installation in
a not very accessible place would be difficult for the maintenance. For your information, the DiSEqC stan-
dard is a trademark by Eutelsat.
If you only have one digital tuner, you will not be able to record a different satellite channel from the
one you are watching.
Altering the settings of the receiver requires to go through the menus. For an easy reading of this User
Guide we have shortened the operations as: MENU / menu / sub-menu. For example, when you read:
The first time you switch your AccessBOX on, your are prompted to enter the desired language for
On Screen Dislplay. Since English is the default value, just press OK. This language selection window is also
shown after resetting the unit (factory settings)
• Go in MAIN MENU / INSTALLATION / LNB & SWITCHES SETUP ,
You will have to:
- Press on MAIN MENU to go to the main menu.
- Press on
key to highlight the INSTALLATION menu.
- Press on OK to select this menu.
- Press on
key to highlight the sub-menu / LNB & SWITCHES SETUP.
- Press on OK to select.
You will notice that the words in bold letters in this user manual are those which
appear on the screen of your television.
Ntc Accessbox-GB 3/11/03 8:43 Page 2