METREL Eutrotest PB Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 127

background image

MI 3108 EurotestPV

Safety and operational considerations

7

2 Safety and operational considerations

2.1 Warnings and notes

In order to maintain the highest level of operator safety while carrying out various tests
and measurements, Metrel recommends keeping your Eurotest instruments in good
condition and undamaged. When using the instrument, consider the following general
warnings:

General warnings related to safety:



The

symbol on the instrument means »Read the Instruction manual with

special care for safe operation«. The symbol requires an action!



If the test equipment is used in a manner not specified in this user manual,
the protection provided by the equipment could be impaired!



Read this user manual carefully, otherwise the use of the instrument may be
dangerous for the operator, the instrument or for the equipment under test!



Do not use the instrument or any of the accessories if any damage is noticed!



Consider all generally known precautions in order to avoid risk of electric
shock while dealing with hazardous voltages!



If the 315 mA fuse blows follow the instructions in this manual in order to
replace it! Use only fuses that are specified!



Do not disassemble or repair the high breaking current fuse block! In case it
fails the entire block must be replaced with a new original one!



Do not use the instrument in AC supply systems with voltages higher than
550 Va.c.



Service, repairs or adjustment of instruments and accessories is only
allowed to be carried out by a competent authorized personnel!



Use only standard or optional test accessories supplied by your distributor!



Consider that protection category of some accessories is lower than of the
instrument. Test tips and Tip commander have removable caps. If they are
removed the protection falls to CAT II. Check markings on accessories! (cap
off, 18 mm tip)…CAT II up to 1000 V
(cap on, 4 mm tip)… CAT II 1000 V / CAT III 600 V / CAT IV

300 V



The instrument comes supplied with rechargeable Ni-MH battery cells. The
cells should only be replaced with the same type as defined on the battery
compartment label or as described in this manual. Do not use standard
alkaline battery cells while the power supply adapter is connected, otherwise
they may explode!

«
...
5
6
7
8
9
...
»

Содержание Eutrotest PB
































































































































Отзывы:

Нет отзывов

Похожие инструкции для Eutrotest PB

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Parker Страницы: 5

Бренд: Bacharach Страницы: 31

Бренд: Backyard Play Systems Страницы: 52

Бренд: Backyard Play Systems Страницы: 19

Бренд: Backyard Play Systems Страницы: 44

Бренд: Bacharach Страницы: 2

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Gary Machinery Страницы: 14

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: Accurate Technology Страницы: 10

Бренд: Gage Bilt Страницы: 28

Pro hunter 2525

Бренд: SprotDog Страницы: 28

Бренд: Barikell Страницы: 32

Бренд: Marani Страницы: 35

Бренд: Honestech Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды