Metallkraft PRM 30 F Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 48

Metallkraft PRM 30 F Скачать руководство пользователя страница 9

Safety

PRM F | Version 1.07 | EN

9

2.6 Safety equipment

2.6.1 Installed safety devices

Emergency stop button

Press the emergency stop button (Fig. 2) located on the control panel control
panel and the machine will stop immediately. The power supply is switched off
or the drives are mechanically disconnected. After the emergency stop button
has been pressed, it must be unlocked by turning so that it can be switched on
again.

Fig. 2: Emergency stop button

WARNING!

Danger to life due to non-functioning safety
devices!

Failure to operate or disable the safety equipment can result
in serious injury or even death.

- Before starting work, check that all safety equipment is in

place and correctly installed.

- Never override or bypass safety devices.

- Ensure that all safety devices are always accessible.

WARNING!

Danger to life due to uncontrolled restarting!

Uncontrolled restarting of the machine can lead to serious
injuries or even death.

- Before switching on again, make sure that the cause of the

emergency stop has been eliminated and all safety devices
are installed and functional.

- Only unlock the emergency stop button if there is no longer

any danger.

«
...
7
8
9
10
11
...
»

Содержание PRM 30 F

















































Отзывы:

Нет отзывов