Mesa 7I43 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 33

background image

7I43 2

HARDWARE CONFIGURATION

GENERAL

Hardware setup jumper positions assume that the 7I43 or 7I43H card is oriented in

an upright position, that is, with the USB connector towards the person doing the
configuration, and the power connector on top right. In the following, "7I43" refers to both
the 7I43 and the 7I43H.

FPGA CONFIGURATION SOURCE

The 7I43's FPGA can be configured via the USB port, The EPP port, or the on card

serial EEPROM. Jumpers W4 and W5 select the configuration source. The 7I43H does
not have the EPP configuration option.

W4

W5

MODE

DOWN

DOWN

EPP (PARALLEL PORT) CONFIG

DOWN

UP

USB CONFIG

UP

DOWN

EEPROM CONFIG

USB POWER

The 7I43 can be powered by the USB host. The maximum power that can be

supplied by a USB host is 450 mA. This will be sufficient for most but not all 7I43
applications. For applications that require more than the 450 mA supplied by the host, the
7I43 has provisions for external power. W6 connects host USB power to the 7I43's power
supplies. To use host power, W6 must be set to the "UP" position. If external 5Vpower is
used, W6 must be set to the "DOWN" position.

WARNING: Connecting an external 5V supply to the 7I43 while W6 is in the "UP"
position and a USB cable connects the 7I43 to a host computer is likely to damage
the computer by feeding external power ‘backwards’ into the USB port!

POWER ENABLE

The 7I43 can be set to power-up only after the USB interface is activated. This is

the suggested operational mode when the 7I43 is interfaced via USB.  For applications
where the 7I43 must operate without the USB interface, This function must be disabled.
W7 controls the power up enable mode. When W7 is in the "UP" position, the 7I43  power
supplies  are  always  enabled.  When  W7  is  in  the  "DOWN"  position,  the  7I43  power
supplies will only be enabled when the USB interface is active.

«
...
4
5
6
7
8
...
»

Содержание 7I43


































Отзывы:

Нет отзывов

Похожие инструкции для 7I43

Бренд: KAPTARLIFT Страницы: 16

Бренд: PACH & COMPANY Страницы: 2

Бренд: M-system Страницы: 3

Бренд: FARFISA INTERCOMS Страницы: 32

Бренд: Infinity Страницы: 24

MICROPUMP 668-400-2

Бренд: Idex Страницы: 33

Бренд: HEEVE Страницы: 16

PROSPORT KRN02210

Бренд: Rain Страницы: 2

Бренд: Mercury Страницы: 3

Бренд: VIA Technologies Страницы: 2

Бренд: Fenix Страницы: 24

Бренд: Eaton Страницы: 15

HydroTap G4 802701

Бренд: Zip Страницы: 24

Бренд: Supersonic Страницы: 6

Бренд: Aiphone Страницы: 2

Бренд: Harmar Mobility Страницы: 16

Бренд: Water Control Страницы: 20

Compact 2 Series

Бренд: DATAEAGLE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды