manualshive.com logo in svg

Mercury Tour Pro 109, Руководство оператора, Страница: 58 / 78

Поделиться
Скачать
Mercury Tour Pro 109 Скачать руководство пользователя страница 58

The trolling motor will drive the bow of the boat along this course, while the

boat itself may be askew to the direction of travel due to current, tide, or wind

conditions. In heading lock—course mode, the trolling motor will automatically

steer to maintain course, and motor speed is user‑selectable. The operator can

use the left turn and right turn buttons or use the heel‑toe operation of the foot

pedal to navigate around obstacles. In extreme current or wind conditions, it

may be necessary to increase the motor speed to maintain the desired

heading.
To exit the heading lock mode from the foot pedal, press the 

heading lock

button. To exit the heading lock mode from the remote press the 

heading lock

or 

manual mode

 buttons on the remote. The trolling motor will emit a

descending chirp and the GPS status indicator light will stop blinking.

Adjusting Motor Speed

If a heading lock mode is selected from manual mode, the trolling motor will run

at the last selected speed. The motor speed can be adjusted by pressing the

increase speed (+)

 button or 

decrease speed (–)

 button on the remote or by

rotating the speed knob on the foot pedal 

counterclockwise

 to increase the

speed or 

clockwise

 to decrease the speed. The trolling motor will emit two

beeps when the user tries to exceed the available motor speed limits.
Cruise control can be used while in either heading lock mode. Refer to 

Using

Cruise Control

.

Adjusting the Heading

While in a heading lock mode, the heading can be adjusted by pressing the 

left

turn

 or 

right turn

 buttons on the handheld remote or by holding the momentary

button down on the foot pedal while steering the foot pedal toe down on the

foot pedal 

toe down

 to steer right or 

heel down

 to steer left. The trolling motor

will resume heading lock—course mode navigation based on the new trolling

motor heading.

Changing the Heading Lock Mode

Heading lock—course mode is the default heading lock mode. To switch to

heading lock—compass mode, press and hold the 

manual mode

 button, then

press the 

2, 1, 2

 buttons in sequence. To switch back to heading lock—course

mode, press and hold the 

manual mode

 button, then press the 

2, 1, 1

 buttons

in sequence.
IMPORTANT: The Pinpoint GPS system will remember which heading lock

mode was last used, and the next time the heading lock button is pressed, the

trolling motor will operate that mode.

TROLLING MOTOR INSTALLATION AND OPERATION

  

52

eng

Содержание Tour Pro 109















































































Отзывы:

Нет отзывов