manualshive.com logo in svg

Mercury Tour Pro 109, Руководство оператора, Страница: 29 / 78

Поделиться
Скачать
Mercury Tour Pro 109 Скачать руководство пользователя страница 29

5. Cut the bounce buster to the new measurement on the unassembled end

of the bounce buster.

a -

Distance between the boat deck and outside surface of the mounting

bracket

b -

Unassembled end

c -

Add 12.7 mm (1/2 in.)

d -

Bounce buster

6. Move the trolling motor into the deployed position.

NOTE:  Removing the steering system from the deployed mount will allow for

easier tightening of the bounce buster screw.
NOTE: The bounce buster will loosen if not fully seated in the bounce buster

pocket.

7. Slide the unassembled end of the bounce buster into the bounce buster

pocket.

8. Use a pencil or piece of tape to mark a line to indicate when bounce

buster is fully seated in the bounce buster pocket. Mark the line 20 mm

(0.79 in.) from the cut end of the bounce buster.

9. Insert and tighten the included bounce buster self‑tapping screw into the

bounce buster pocket.

a -

Bounce buster pocket

b -

Self‑tapping screw

c -

Bounce buster

b

70135

d

a

c

a

c

b

70137

TROLLING MOTOR INSTALLATION AND OPERATION

eng

23

  

Содержание Tour Pro 109















































































Отзывы:

Нет отзывов