Mercury MerCruiser Axius 350 MAG Скачать руководство пользователя

Страница: 88 / 151

Section 4 - Specifications

Page 80

90-864197084 NOVEMBER 2008

Models

Axius and Axius SeaCore

350 MAG

Axius and Axius SeaCore

377 MAG

Power

224 kW (300 hp)

238 kW (320hp)

Number of cylinders

Displacement

5.7 L (350 cid)

6.2 L (377 cid)

Bore and Stroke

101.6 × 88.39 mm

(4.00 × 3.48 in.)

101.6 × 95.25 mm

(4.00 × 3.75 in.)

Compression ratio

9.4:1

9.0:1

Idle RPM in neutral

600

Specified WOT RPM range

4800–5200

Minimum oil pressure at idle

41 kPa (6 psi)

Thermostat (seawater‑cooled models)

71° C (160° F)

Thermostat (closed cooled models)

77° C (170° F)

Timing at idle

Not Adjustable

Firing order

1‑8‑4‑3‑6‑5‑7‑2

Electrical system

12‑Volt Negative (‑) Ground

Alternator rating

65 A

Recommended minimum battery rating

800 CCA, 1000 MCA, or 190 Ah

Spark plug type

AC Platinum (AC 41‑993)

Spark plug gap

1.5 mm (0.060 in.)

Engine Specifications

Axius 350 MAG, Axius SeaCore 350 MAG with Emissions Control

NOTE: Performance specifications are obtained and corrected in accordance with SAE J1228/ISO 8665 Crankshaft Power.

All measurements are taken with the engine at normal operating temperature.

RPM range is measured using an accurate service tachometer with the engine at normal operating temperatures.

Oil pressure must be checked with the engine at normal operating temperature.
NOTE: Oil pressure specifications are for reference and may vary.

Propshaft power

224 kW (300 hp)

Displacement

5.7 L (350 cid)

Alternator amperage

Hot

72 A

Cold

65 A

RPM

WOT

4800–5200

Rev limiter

5350

Idle in neutral

550

Minimum oil pressure

At 2000 RPM

124 kPa (18 psi)

At idle

41 kPa (6 psi)

Thermostat

Seawater‑cooled models

71° C (160° F)

MPI models with closed cooling

77° C (170° F)

Timing at idle

Not Adjustable

Firing order

1‑8‑4‑3‑6‑5‑7‑2

Minimum battery rating

Non‑DTS models

750 CCA, 950 MCA, 180 Ah

DTS models

800 CCA, 1000 MCA, 190 Ah

Spark plug type

AC Platinum (AC 41‑993)

Spark plug gap

1.5 mm (0.060 in.)

Содержание MerCruiser Axius 350 MAG
























































































































































Результаты поиска

Содержание MerCruiser Axius 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius 350 MAG

Бренды по названию

Популярные бренды