background image

Section 3 - On The Water 

Page  64

90-864197084   NOVEMBER  2008

The horizontal and vertical displacement of the vessel from the cross hairs is proportional to the position error reported by

the GPS.

Each gradation of color in the circular target on the VesselView screen is equivalent to 5 meters of error. If the boat exceeds

20 meters of error, then the boat is located at the edge of the circle. The boat continues to try to correct until Skyhook is

disengaged.

Skyhook screen on VesselView

a -

Location where Skyhook is set

b -

Location where boat is relative to set

location

c -

5 meter gradation

d -

Engine RPM

Disengaging (Deactivating) Skyhook

IMPORTANT: Under most circumstances, both engines and drives must be operational to achieve acceptable Skyhook

performance. If the necessary reference signals from an engine or drive become unavailable, Skyhook automatically

disengages.
1. To disengage the Skyhook, you must do one of the following:

Press the "SKYHOOK" button on the Axius Premier CAN Trackpad.

Move any ERC lever out of neutral.

Move the joystick.

NOTE: In each method, the light on the Axius Premier CAN Trackpad for the "SKYHOOK" button will turn off.

Auto Heading

Auto Heading allows the boat to automatically maintain a compass heading while the boat is underway.

Engaging Auto Heading

1. Place at least one running engine in forward gear.

NOTE: Auto Heading does not function with the ERC levers in neutral or reverse.

2. Steer the boat to the desired compass heading.

a

b

c

d

27716

Содержание MerCruiser Axius 350 MAG
























































































































































Отзывы: