background image

Section 5 - Maintenance 

Page  92

90-864197084   NOVEMBER  2008

NOTE: Add coolant only when engine is at normal operating temperature.

1. Remove the fill cap from the coolant recovery bottle.
2. Fill to the "FULL" line with the specified coolant.

Tube Ref No.

Description

Where Used

Part No.

122

Extended Life Antifreeze/

Coolant

Closed Cooling System

92-877770K1

3. Install the fill cap onto the coolant recovery bottle.

Changing

Contact your authorized Mercury MerCruiser dealer.

Sterndrive Gear Lube

Checking

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by law. Use caution not to spill oil, coolant,

or other fluids into the environment when using or servicing your boat. Be aware of the local restrictions governing the disposal

or recycling of waste, and contain and dispose of fluids as required.

NOTE: The level of gear lube oil will fluctuate during operation. Check the oil level with the engine cold, before starting.

1. Check the gear lube level in the gear lube monitor. Keep the level within the recommended operating range.

a -

Gear lube monitor

b -

Typical closed cooled

model

c -

Typical seawater cooled

model

2. Inspect the lubricant condition. If any water is visible at the bottom of the gear lube monitor, if water appears at the fill and

drain plug hole, or if the gear lube appears discolored, contact your authorized Mercury MerCruiser dealer immediately. These

conditions can indicate a water leak in the sterndrive.

Filling

IMPORTANT: If more than 59 mL (2 fl oz) of High Performance Gear Lubricant is required to fill the monitor, a seal may be leaking.

Damage to the sterndrive unit may occur due to lack of lubrication. Contact your authorized Mercury MerCruiser dealer.
1. Remove the gear lube monitor cap.
2. Fill the monitor with the specified fluid so that the level is in the operating range. Do not overfill.

Shown removed for visual clarity

a -

Gear lube monitor cap

b -

Operating range (full) line

a

32539

a

b

c

b

a

7884

Содержание MerCruiser Axius 350 MAG
























































































































































Отзывы: