Mercury 25 Jet 4-Stroke Скачать руководство пользователя страница 89

Страница: 89 / 122

MAINTENANCE

3. Set the spark plug gap to specifications.

ob00680

Spark Plug Gap
Spark plug

0.80‑0.90 mm (0.031‑0.035 in.)

4. Before installing spark plugs, clean off any dirt on the spark

plug seats. Install plugs finger tight, and then tighten to the

specified value.

Description

lb. in.

lb. ft.

Spark plug

Fuse Replacement ‑ Electric Start Models

IMPORTANT: Always carry spare SFE 20 AMP fuses.
The electric starting circuit is protected from overload by an SFE

20 AMP fuse. If the fuse is blown, the electric starter motor will not

operate. Try to locate and correct the cause of the overload. If the

cause is not found, the fuse may blow again.

1. Open the fuse holder and look at the silver colored band inside

the fuse. If band is broken, replace the fuse. Replace fuse with

a new fuse with the same rating.

15917

a -

Good fuse

b -

Blown fuse

Содержание 25 Jet 4-Stroke



























































































































Результаты поиска

Содержание 25 Jet 4-Stroke

Отзывы:

Бренды по названию

Популярные бренды

Mercury 25 Jet 4-Stroke, Руководство пользователя

Результаты поиска

Содержание 25 Jet 4-Stroke

Отзывы:

Бренды по названию

Популярные бренды