Mercury 25 Jet 4-Stroke Скачать руководство пользователя страница 59

Страница: 59 / 122

OPERATION

WARNING

Avoid injury, death or property damage resulting from collision

due to loss of directional control. Directional control is derived

from the water jet thrust. Caution should be exercised when

maneuvering at higher speeds in areas where debris (weeds,

logs, gravel, etc.) could be picked up into the jet drive. This can

cut off or reduce the water jet thrust, thereby directly affecting

boat directional control. Boat directional control can also be

substantially reduced or lost altogether by a sudden loss of power

such as running out of gas, quickly backing off throttle, turning

off ignition switch, or activating lanyard stop switch. Remember

you ability to take evasive action is dependent on sufficient water

jet thrust to control the boat.

While steering the boat at engine speeds above idle, the boat will

respond quickly; but due to the relatively flat‑bottom hulls and lack

of a gearcase in the water, the boat will tend to skid on turns. Turns

must be started early and use sufficient power to maintain steering

control.

Mooring The Boat

Be sure to tilt the jet drive out of the water when the boat is pulled

onto a beach or tied to a dock in shallow water. Failure to do this

may cause the water intake housing to fill with sand or debris and

could prevent the outboard from cranking over for starting.

Water Intake Blockage

WARNING

Avoid injury resulting from contacting the rotating impeller.

Always shut off the engine before attempting to remove a

blockage from the water intake.

A large amount of debris being drawn into the water intake may

result in a loss of power. Intake suction holding debris against the

grate will result in restricted water flow. Shutting the engine off may

allow the debris to fall off the intake grate allowing full power to be

restored. If debris does not fall off the intake grate, the engine must

be shut off and debris physically removed from the grate.

Содержание 25 Jet 4-Stroke



























































































































Результаты поиска

Содержание 25 Jet 4-Stroke

Отзывы:

Бренды по названию

Популярные бренды

Mercury 25 Jet 4-Stroke, Руководство пользователя

Результаты поиска

Содержание 25 Jet 4-Stroke

Отзывы:

Бренды по названию

Популярные бренды