Mercury 25 Jet 4-Stroke Скачать руководство пользователя страница 105

Страница: 105 / 122

ENGINE INSTALLATION

Installation Information

BOAT HORSEPOWER CAPACITY

WARNING

Using an outboard that exceeds the maximum horsepower limit

of a boat can: 1) cause loss of boat control 2) place too much

weight at the transom altering the designed flotation

characteristics of the boat or 3) cause the boat to break apart

particularly around the transom area. Overpowering a boat can

result in serious injury, death or boat damage.

Do not overpower or overload your boat. Most boats will carry a

required capacity plate indicating the maximum acceptable power

and load as determined by the manufacturer following certain

federal guidelines. If in doubt, contact your dealer or the boat

manufacturer.

U.S. COAST GUARD CAPACITY
MAXIMUM HORSEPOWER XXX

MAXIMUM PERSON
CAPACITY (POUNDS)

XXX

MAXIMUM WEIGHT
CAPACITY

XXX

ob00306

START IN GEAR PROTECTION

WARNING

Avoid serious injury or death from a sudden unexpected

acceleration when starting your engine. The design of this

outboard requires that the remote control used with it must have

a built in start in neutral only protection device.

The remote control connected to the outboard must be equipped

with a start in neutral only protection device. This prevents the

engine from starting in gear.

Содержание 25 Jet 4-Stroke



























































































































Результаты поиска

Содержание 25 Jet 4-Stroke

Отзывы:

Бренды по названию

Популярные бренды

Mercury 25 Jet 4-Stroke, Руководство пользователя

Результаты поиска

Содержание 25 Jet 4-Stroke

Отзывы:

Бренды по названию

Популярные бренды