manualshive.com logo in svg

Mercury 25 Jet 4-Stroke, Руководство пользователя

Поделиться
Скачать
Mercury 25 Jet 4-Stroke Скачать руководство пользователя страница 74

MAINTENANCE

68

• Check and adjust valve clearance, if necessary.

1.

• Check the power trim fluid. See Checking Power Trim Fluid.
• Inspect the battery. See Battery Inspection.
• Check the control cable adjustments.

1.

• Inspect the timing belt. See Timing Belt Inspection.
• Check tightness of bolts, nuts, and other fasteners.
• Check  cowl  seals  to  make  sure  seals  are  intact  and  not

damaged.

• Check  internal  cowl  sound  reduction  foam  (if  equipped)  to

make sure foam is intact and not damaged.

• Check that the intake silencer (if equipped) is in place.
• Check that the idle relief muffler (if equipped) is in place.
• Check for loose hose clamps and rubber boots (if equipped)

on the air intake assembly.

EVERY 300 HOURS OF USE OR THREE YEARS

• Replace the water pump impeller (more often if overheating

occurs or reduced water pressure is noted).

1.

BEFORE PERIODS OF STORAGE

• Refer to storage procedure. See Storage section.

Top Cowl Removal and Installation

REMOVAL

1. Unlock the rear latch by pulling lever up.

10190

Содержание 25 Jet 4-Stroke



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды