manualshive.com logo in svg

Mercury 25 Jet 4-Stroke, Руководство пользователя

Поделиться
Скачать
Mercury 25 Jet 4-Stroke Скачать руководство пользователя страница 100

TROUBLESHOOTING

94

• Spark plugs fouled or defective. Refer to Maintenance section.

Engine Runs Erratically

POSSIBLE CAUSES

• Overheating ‑ Warning horn not working.
• Low oil pressure. Check oil level.
• Spark plugs fouled or defective. Refer to Maintenance section.
• Incorrect setup and adjustments.
• Fuel is being restricted to the engine.

a. Engine  fuel  filter  is  obstructed.  Refer  to  Maintenance

section.

b. Fuel tank filter obstructed.
c. Stuck  anti‑siphon  valve  located  on  permanently  built‑in

type fuel tanks.

d. Fuel line is kinked or pinched.

• Fuel pump failure.
• Ignition system component failure.

Engine Over‑Speed (Excessive RPM)

POSSIBLE CAUSES

• Outboard mounted too high on the transom.
• Worn jet pump impeller or liner.
• Incorrect jet pump impeller clearance adjustment.
• Tilting the outboard out beyond a vertical position.
• Cavitation of the impeller due to rough water or obstruction in

the boat hull.

• Blockage of the water intake.

Performance Loss

POSSIBLE CAUSES

• Throttle not fully open.
• Damaged impeller.
• Incorrect engine timing, adjustments, or setup.
• Boat overloaded or load improperly distributed.

Содержание 25 Jet 4-Stroke



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды