Mercury 25 Jet 4-Stroke Скачать руководство пользователя страница 86

Страница: 86 / 122

MAINTENANCE

Assemble steering link rod to steering cable with flat washer and

nylon insert locknut. Tighten locknut until it seats, then back nut off

1/4 turn.
Assemble steering link rod to engine with bolt, locknut, spacer, and

flat washers. Torque locknut to specifications.

9691

a -

Bolt (10‑898101018)

b -

Flat washer (12‑95392‑10)

c -

Spacer (23‑853826001)

d -

Nylon insert locknut (11‑16147‑‑3)

e -

Install steering link rod into side hole

f -

Nylon insert locknut (11‑16147‑‑3) (tighten until seats

then back off 1/4 turn)

Description

lb. in.

lb. ft.

Nylon insert locknut "d"

Nylon insert locknut "f"

Tighten until seats, then back off ¼ turn

Corrosion Control Anode

Your outboard has corrosion control anodes at different locations.

An anode helps protect the outboard against galvanic corrosion by

sacrificing its metal to be slowly corroded instead of the outboard

metals.

Содержание 25 Jet 4-Stroke



























































































































Результаты поиска

Содержание 25 Jet 4-Stroke

Отзывы:

Бренды по названию

Популярные бренды

Mercury 25 Jet 4-Stroke, Руководство пользователя

Результаты поиска

Содержание 25 Jet 4-Stroke

Отзывы:

Бренды по названию

Популярные бренды