manualshive.com logo in svg

Mendota FV41-ARCH, Руководство по установке

Поделиться
Скачать
Mendota FV41-ARCH Скачать руководство пользователя страница 53

85-03-00944 

53 | 

P a g e

 

 

 

Remote Control Transmitter Functions 

 

NOTE

: The Ignition Module Receiver will “beep” once 

every time a Remote Transmitter Key is pressed, sig-
naling that the command has been received. 

Identify the four function buttons on the Remote 
Transmitter:

 

 

1. 

ON/OFF KEY

: This button turns 

the system ON or OFF. When 
this button is pressed and the 
system is OFF, the pilot light will stay ON if 
the “Standing Pilot Switch” is in the ON posi-
tion. 

2. 

THERMOSTAT KEY

: This button, when pressed after the ON/OFF KEY is pressed and the sys-

tem is ON, will allow the selection of three modes: Manual Operation, Normal Thermostat and 
Smart Thermostat. 

b. 

Manual Mode

: In this mode, the room temperature is ignored and the fireplace can be turned ON indefinitely. 

The room temperature rise has no effect on this mode.  All other functions such as fan speed control, flame 
height control, secondary burner On/OFF control and Accent Light ON/OFF controls will be manually control-
lable. 

c. 

Normal Thermostat

: In this mode, the fireplace 

will stay functioning until the room temperature in-
creases 1

o

F above the Set Point Temperature. To 

increase the Set Point Temperature, Press the UP 
button until the desired temperature is displayed in 
the SET POINT TEMPERATURE window. The fan 
will turn on 5 minutes after fireplace startup and will 
turn off 12-1/2 minutes after the flames turn off, in 
this mode. The flame height can be adjusted while 
the fireplace is functioning, fan speed can be ad-
justed after 5 minutes of startup. Secondary burner 
can be turned On or Off at any time after startup. 
The Accent Light can be turned on or off any time 
after startup. 

d.

 

Smart Thermostat

: In this mode, all other func-

tions except the flame height adjustment are allowed. Manual flame height adjustment is not allowed in this 
mode.  The Smart Thermostat function adjusts the flame height in accordance to the difference between the 
set point temperature and the actual room temperature.  As the room temperature gets closer to the set point 
temperature, the Smart Function automatically modulates the flame down.

  

3. UP/DOWN 

KEY: 

This key is used to increase or decrease the Set Point Temperatures, Flame 

Height and Fan Speed and to toggle between Accent Light ON/OFF and Secondary Burner 
ON/OFF

. 

 

4.  MODE SELECTION KEY: 

This key is used to toggle between the various function icons : Flame 

Height, Fan Speed, Accent Light and Secondary Burner.

 

 

SMART

ON

OFF

SMART

MODE

NORMAL

THERMOSTAT

MANUAL

MODE

68

Hi

MAX

MAX

Hi

OFF

76°

F

F

76°

ON

SMART

76°

F

Содержание FV41-ARCH









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды