manualshive.com logo in svg

Mendota FV41-ARCH, Руководство по установке

Поделиться
Скачать
Mendota FV41-ARCH Скачать руководство пользователя страница 18

85-03-00944 

18 | 

P a g e

 

 

FINISHING MATERIALS INSTALLATION 

All finishing materials that surround this fireplace’s arch profile must extend out from the face surface of this fireplace 1 
inch.  

Tiles and Faux Rock 

If installing Tiles or Faux Rock, first install a ½” thick (minimum) Cement Board (Hardibacker or Durock Brand) over the 
face of the fireplace and framing members. Follow by applying Thinset mortar (no polymer additives) using ¼” square 
notched trowel on the cement board surface.  Finally, install tile to reach a finish material depth of 1 inch.   

Marble and Granite Slabs 

If installing Marble or Granite slabs as fascia materials, specify that the inner edges that will be adjacent to the Glass Door 
are polished. Rough Framing should be created at 19” depth with the front surface of this fireplace protruding out ½” from 
the framing surface. 

NOTE: On the left side of this unit, rotate the 2x4 stud so the 1-1/2” thickness is towards the 

control module box.

  Install 1/2'” thick drywall on framing members so that its outer surface is flush with the front face of 

this fireplace.  Attach Marble or Granite slabs to face of unit and to drywall surface using adhesive that does not offgas 
when hot. 

In the area defined as “NONCOMBUSTIBLE ZONE” [FIGURE 7], only NONCOMBUSTIBLE MATERIALS ARE 
ALLOWED. 

When this fireplace is installed in a framed cavity that is 19-1/2” deep, the facing material finishing guide will pro-
trude out into the room 1 inch. Build finishing materials to 1 inch thickness and use the built-in guides for edge 
alignment of fascia material. Consult section “FRAMING DEPTH and FINISHING GUIDES”. 

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 

 
WARNING: 

 The cross hatched areas labeled as “NONCOMBUSTIBLE ZONE” must be covered with noncombustible finishing 

materials that is 1-inch thick, minimum.  DO NOT ALLOW COMBUSTIBLE FACING MATERIALS TO ENCROACH IN THIS 
AREA! Conforming combustible mantels may be installed on top of the non-combustible facing in the top noncombustible zone. 

 

 

NON-COMBUSTIBLE ZONE

(ALL HATCHED AREAS)

FINISHING GUIDES

A

Содержание FV41-ARCH









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды