manualshive.com logo in svg

Mendota FV41-ARCH, Руководство по установке

Поделиться
Скачать
Mendota FV41-ARCH Скачать руководство пользователя страница 20

85-03-00944 

20 | 

P a g e

 

 

BACKUP DC POWER INLET PORT INSTALLATION 

Under normal conditions when AC power is 
available, this appliance is designed to oper-
ate on 110 VAC power. During power outag-
es, it is designed to operate using 6 V DC 
backup power.  This appliance is supplied 
with a DC power inlet harness, a single gang 
outlet box and two single cover plates. In ad-
dition, a 4 X AA size battery pack and a con-
nector harness is also supplied. 

INSTALLATION:

 It is important that you in-

stall the supplied harness, outlet box and 
cover plate on the left side of this appliance. 
The DC Power Inlet harness is 6 feet long, 
allowing installation of the single gang box up 
to 5 feet to the left of this appliance. Install the 
single gang box at a maximum height of 18” 
to the center of the box or match the mounting 
height of this single gang box with the height 
of other AC outlets that are installed in the 
same room as this appliance. WARNING: DO 
NOT STAPLE the 6’ DC Power Inlet Harness 
to the wall studs. 
 

COVER PLATES

: Two cover plates are sup-

plied and are White and Beige in color. If the home décor requires a different color other than the two supplied colors, ob-
tain one from a local hardware store. Make certain that the cover you obtain is exactly the same dimensions as the ones 
supplied with this fireplace. 

DECAL INSTALLATION

: A notification decal (label) is supplied with this fireplace 

that aids in identifying the DC Power Inlet. Attach this label to cover plate once 
installation is complete and verified. 

INSTRUCT HOMEOWNER

: Demonstrate to the homeowner how to attach the 

backup DC power pack during power outages. Instruct homeowner to retain the 
DC battery pack and the connecting harness in a safe and secure place for use 
during power outages.  

 

 

ATTACH DECAL 
TO COVER PLATE.

Содержание FV41-ARCH









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды