background image

D33363 | Date 06/2016  

39

Menu functions

7.3.4 Timer Mode

Here, you can choose whether the digital backwards counter with 

target time setting (see page 27, timer) should run setpoint-

dependent or not – this determines whether the timer should 

not start until a tolerance band of ±3 K around the set 

temperature is reached (Fig. 23, B) or whether it should start 

right after activation (A).

t

Timer

t

Timer

A

B

°C/°F

t

6 K

ž

ž

Fig. 23

 Timer Mode

Timer independent of setpoint: Timer starts right after activation

g

Timer setpoint-dependent: Timer does not start until tolerance band is reached

p

p

g

p

g

If the temperature tolerance band is exceeded in setpoint-dependent operation, the timer will 

be interrupted and only be resumed when the setpoint temperature has been reached again.

7.3.5  Type of the slide-in unit (Grid or Shelf)

Here, you have to set the type of the slide-in unit (grid or shelf) 

used. The selection Shelf enables you to adjust the control 

function to the different air flow characteristics in the interior 

when using optional sliding shelves instead of the grids that are 

part of the standard delivery.

7.3.6 Remote control

In the setup entry 

Remote control

, you can set whether the 

appliance should be controlled via remote control and if 

so, in which mode. These settings are available:

Ź

Off

Ź

Read Only

Ź

Write

Ź

Write+Alarm

When the appliance is in remote control mode, the 

symbol appears in the temperature display. In the 

settings 

Write

 and 

Write+Alarm

, the appliance cannot 

be controlled at the ControlCOCKPIT until the remote 

control has been switched off (setting Off) or set to 

Read

Only

.

In order to use the remote control function, program-

ming skills and special libraries are required.

SETUP

Unit

IP address

255.145.136.225

Subnet mask

255.255.0.0

Alarm temp

°C

F

TWW

TWB

Timer mode

Unit

IP adress

255.145.136.225

Subnet mask

255.255.0.0

°C

°F

Timer mode

Alarm temp

TWW

TWB

Slide-in unit

Grid         Shelf

Setup

Balance

Remote Control

   

Off

Gateway                192.168.5  .1

+30 %

2/2

23

.2°C

TEMP

Set 180

.0°C

Содержание IF 1060

















































Отзывы: