background image

 

 
 
Model FL-PWJ Power Supply & FL-LHJ 
Lamphouse

 

 

1. Introduction 

 

The Meiji Techno FL-PWJ Epi-Fluorescence Illuminator Power Supply is a 
precision engineered product incorporating efficient, silent-running switchmode 
power supply technology delivering smooth, regulated current. 
 
The FL-PWJ Power Supply is designed only to support 100 watt HBO DC arc 
lamps. 
 
The advanced switchmode design provides constant, low-noise DC power that 
automatically adjusts for the condition of the DC lamp in circuit. 
 
The FL-PWJ Power Supply comes standard with a panel mounted circuit breaker 
and provides accidental unplug protection to guard against laboratory mishaps. 
 
A panel mounted Elapsed Time Panel Meter keeps track of the DC arc lamp 
hours in use so replacements can be easily accommodated. 
 
The reset button on the panel meter resets to “zero” when arc lamps are 
replaced. 
 
This system was designed for easy plug-n-play integration with 100 watt HBO 
illumination commonly used in fluorescence microscopy work with no additional 
adjustments necessary for the lifespan of the arc lamp. 
 
The FL-PWJ Power Supply can be used with the TC Series Inverted Epi-
Fluorescence Microscope and comes standard on the MT6000 Series Epi-
Fluorescence Upright Biological Models. 

 
 
 
 
 
 

Содержание FL-LHJ



























Отзывы: