MegiQ VNA04 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 64

MegiQ VNA04 Series Скачать руководство пользователя страница 9

VNA0440

–

VNA0440e

VNA0460

–

VNA0460e

user manual V3.1

www.megiq.com

- 9 -

4.

Installation

•

Software and hardware installation

•

VNA modes

Software installation

To install the VNA software, locate the file ‘SetupMiQVNA.exe’ on the USB stick or
download directory and execute this file. The software installation has only a few choices
to make, or to leave at default, and is straightforward.

By default, the software is installed in ‘Program files (x86)\MegiQ\VNA’. The
subdirectory ‘Data’ contains an example measurement session file. The subdirectory
‘Driver’ contains a driver description file for those installations that need this.

The manual ‘MegiQ VNA Software Setup’ contains details about the installation in
different Windows versions.

Command line options

MiQVNA [-c] [session file]

-c: Clean all user settings and return to installation state.

Session file: load a session file when starting up.

Hardware installation

The hardware installation has some different procedures depending on the operating
system and version. The procedures for hardware installation are described in the software
installation manual.

In Windows 10 there is no hardware installation procedure, just connect the VNA to the
computer and Windows will install the correct driver.

VNA Operating modes

The VNA has two operating modes:

Bootloader

and

VNA mode

.

When the VNA is connected to the USB port without the DC supply connected it will
enter the bootloader. The LEDs on the front panel will light only dimly. The bootloader
only allows uploading new firmware or control files. The normal VNA mode also
provides these services. The bootloader is a safety feature in the (extremely rare) case the
VNA application would be messed up.

When the VNA is connected to both USB and DC power it will enter the normal VNA
mode and the LEDs will light up in green and blue (VNA04x0e).

The PC application software can interact with the VNA in both modes but the bootloader
only provides support for uploading and installing firmware.

«
...
7
8
9
10
11
...
»

Содержание VNA04 Series

































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды