MegiQ VNA04 Series Скачать руководство пользователя страница 59

Страница: 59 / 64

VNA0440

–

VNA0440e

VNA0460

–

VNA0460e

user manual V3.1

www.megiq.com

- 59 -

VNA

Shows information about the currently connected VNA and provides some VNA control.

•

VNA Info: information about the hardware such as product name, serial number,
versions, options and a unique device ID number.

•

Autoconnect: When checked, the software will automatically connect to the VNA
when it is detected.

•

Connection: Controls the connection with the VNA.

•

Test VNA: Runs a VNA hardware test and reports the result. The VNA must be
rebooted after this test (newer software versions will automatically reboot the VNA).

•

Copy Info: Copy the list info.

•

Firmware: Opens a screen to upload new firmware.

Connection screen

When running the VNA software in a virtual machine, the software may not automatically
detect when the VNA is connected.

Содержание VNA04 Series

































































Результаты поиска

Содержание VNA04 Series

Отзывы:

Бренды по названию

Популярные бренды

MegiQ VNA04 Series, Руководство пользователя

Результаты поиска

Содержание VNA04 Series

Отзывы:

Бренды по названию

Популярные бренды