Megger Baker DX Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 156

background image

Procedures for Testing with the DX Host

megger.com

115

Low-voltage Armature or Coil Tests Using the DX Host

Low-voltage armature or coil mode is used to plot resistance, inductance, phase angle, and
impedance measurements taken over different coils or over different armature bars (windings).
For example, in the case of testing a DC armature, you can take test measurements on each bar
on the commutator. All measurements are made on each coil or armature bar. The results are
plotted with respect to the different coils tested.

The display control buttons at the top move you through which coil or armature bar
measurement you want to see. The buttons along the right edge are used to select the type of
test measurement you want to plot.

Figure 128. Low-voltage armature or coil mode screen elements.

In the submenu, the first icon from the left—the

Armature Coil Mode

icon—shows you that

you are in low-voltage armature or coil mode. The

Bar Graph

icon identifies the display format

selected. Touching the icon allows you to change the type. The frequency displayed is shown by
the next icon, which again can be changed by touching the icon. The frequency is typically that
used to operator the device under normal conditions.

The fourth icon—

Single Coil

in this case—shows the type of coil being tested. That selection

can also be changed by touching the icon. This icon is a notation in the result that also appears
in the report when printed.

«
...
123
124
125
126
127
...
»

Содержание Baker DX





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Baker DX

Бренд: E+E Elektronik Страницы: 32

Бренд: Hama Страницы: 6

Бренд: Roland Страницы: 15

Бренд: Olympus Страницы: 362

Бренд: Olympus Страницы: 8

Бренд: janitza Страницы: 48

Бренд: Teledyne Hastings Instruments Страницы: 54

Бренд: Burkert Страницы: 192

Бренд: Tohnichi Страницы: 12

Concert Performer Series Digital Piano CP110

Бренд: Kawai Страницы: 149

Бренд: Sper scientific Страницы: 56

Бренд: CAS Corporation Страницы: 20

miniSERIES Series

Бренд: Valeport Страницы: 25

Seeker 400 Series

Бренд: General Страницы: 24

Бренд: shelyak Страницы: 45

Бренд: PASI Страницы: 59

Бренд: Lutron Electronics Страницы: 10

Бренд: NIEUWKOOP Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды