MEGA 2400 OPERATE
4
I. DISARMING WITHOUT A TRANSMITTER
(Alarm Feature
II
-
6
Programming)
OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE:
(Factory Default Setting)
The override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ign
ition switch to 'ON’ position. Alarm will sound.
2. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter
disarm mode. You can now start and operate the vehicle normally.
OVERRIDE THE ALARM WITH PASSWORD PIN CODE:
(
Alarm Feature
II
-
6
Programming
)
Unlike valet switch easily found, and defeated, this security system allows the consumer to program
a password pin code. Offering a higher level of security.
1. Enter the vehicle and turn the ignition switch to 'O
N’ position. Alarm will sound.
2. Within 5 seconds, enter your chosen the first digit code by press and release the Valet Switch.
When finished above procedures, system's siren stop alarming, parking light stop flashing, but
the vehicle cannot be start and drive away.
3.
Within 15 seconds of the last digit code enter (the 1st code), turn the Ignition Switch “OFF” and
then “ON”.
4. Within 15 seconds, enter your chosen of the second digit code by press and release the Valet
Switch.
5.
Turn the ignition switch “OFF” position. [4] Chirps form siren/horn, [3] flash from parking light to
indicate the system was disarmed.
Note:
You must override the alarm within 60 seconds. If not, the system will automatically re-arm.
EXAMPLE: To Override The System With The Password Code 83, you would;
1. Enter the vehicle and turn the ign
ition switch to 'ON’ position. Alarm will sound.
2. Within 5 seconds, Press and Release the Valet Switch 8 times. When finished above procedure,
system's siren stops alarming, parking light stop flashing, other sensors stop trigger, but the
vehicle cannot be start and driven away.
3. Within 15 seconds of the last digit code enter (the first
code), turn the Ignition Switch “Off” and
then “ON”.
4. Within 15 seconds, Press and Release the Valet Switch 3 times
5.
Turn the Ignition Switch to “Off” position. [4] Chirps form siren/horn, [3] flash from parking light to
indicate the system was disarmed.
J. VALET MODE
(System in Disarm or Valet mode)
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand
your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all
alarm functions and remote start functions are bypassed, however the remote panic feature and
remote door locks will remain operational. To use the valet mode, the system must first be
disarmed either by using you remote transmitter, or by operating the Manual override sequence.
Enter Valet Mode:
1. From the
disarmed condition, turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds until the LED turns on. The LED wills remain on as
long as the system is in 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'on'.
2. Push and hold valet switch for 2 seconds, The LED wills turns off indicate the system are exiting
the valet mode.
K. CAR LOCATOR
Under armed mode, press the
button to active car locator function. The siren will chirp 6 times.
The parking light will flash 12 times, for you to easily locate your car.
L. PANIC FUNCTION
The transmitter can be used as a remote panic switch to manually trigger the alarm in case
emergency.
1. Press and hold the
button for 3 second. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be suspended. The
transmitter
and
buttons can be used to lock and unlock the door (if the option is installed),
however once the
button is pressed, the vehicle’s starter disable device, (where installed) will
be enable allowing the vehicle to start.
3. To stop the alarm, press and hold the transmitter
or
button on the transmitter again for 3
seconds. Also if any transmitter buttons other than
or
button is pressed and released, the
panic mode will be turned off immediately.
