MEGA 2400 OPERATE
6
This security system is equipped with circuitry that will allow the unit to remember its alarm state if
the power is lost and then reconnected.
T. SECOND VEHICLE OPERATION
Your 5-button remote transmitter can be utilized to control a 2
nd
vehicle keyless entry system. To
program the remote control transmitter to a 2
nd
vehicle, follow the instruction for Transmitter
programming. All programming parameters be the same except for the following:
1. Prior to pushing any buttons on the transmitter. Press the
●
button 1
st
on the transmitter.
2. Once the
●
is pressed the LED on the transmitter will illuminate for 3.5 sec. to indicate the 2
nd
transmitter pin code has built in.
3. While the LED is illuminated, press any button on the remote control transmitter to control a 2
nd
vehicle keyless entry system.
U. 2-WAY UPGRADE
This unit is capable of 2-way communication to notify the owner if anyone is trying to tamper with
the vehicle or to confirm remote start operation. If you would like to upgrade this unit to a 2-way
system by purchasing a 2-way LCD transceiver, please contact your authorized reseller.
REMOTE START OPERATION:
A. REMOTE START THE VEHICLE:
1. Press
button twice on the transmitter.
2. The parking light will activate to indicate the remote start received the signal.
3. The engine will start approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking light will turn on again and climate
controls will activate and adjust the vehicles interior temperature to your preset setting.
5. The vehicle will run for 5 to 30 minute cycle and automatically shut down.
Note:
The Remote Start Unit will not start the vehicle if any one of the following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position. (If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”
SAFE START (Child safety mode)
(See Start Feature
I
– 5
Programming)
Factory defaults setting to press the
button twice on the transmitter to start the vehicle.
Programming this feature to eliminate an accidental remote start, when kids enter this transmitter, it
requires the user press the transmitter
and
buttons at the same time to start the vehicle.
B. OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START:
To operate the vehicle while engine running on the remote start:
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note:
If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
C. TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition.
This feature is useful for occasions when you wish to exit and lock the vehicle for short periods, but
would like to leave the motor running and the climate control on.
1. Before turning off the engine, press the
button twice on the transmitter and the LED indicator
will flash 3 times to confirm enter.
2. Turn the ignition key to OFF position. The engine will stay running.
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.
E. TURBO TIMER MODE:
(See Start Feature
“I - 6”
Programming)
Turbo timer mode keeps the engine running after arriving at you destination for a programmable
period of
1/ 3 or 5 minutes, This allows the system’s time to conveniently cool down the turbo after
you have left the vehicle. To activate:
1. While engine is running, place the transmission gear in the park position and pull up the hand
brake.
2. Before turning off the engine, press and release
and
buttons at the same time.
-- The parking light wills turn on to indicate the remote start has entered turbo charge mode. --
3. Pull off the “Ignition Key” from the key cylinder.
-- Engine keeps running.
–
4. Exit and secure the vehicle.
--
Engine continues running until the pre-programmed time elapsed.
--
