Megalarm MEGA 250, Руководство по установке

Страница: 12 / 20

2. Push the Valet switch 2 times and holding in on 2
nd
push until one chirp with a long chirp is hearing and
the LED start to flash then release the Programming switch. You are now in the feature ‘I’ programming
mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
a.
The horn chirps and LED pause will indicate newly setting.
b.
The factory default settings is always [2] LED flash, [2] horn chirp.
4 Depress the transmitter button ‘A’ again to change the feature. Simple keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
a.
In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] horn chirp.
b.
Press button ‘A’ again, the module would advance to [3] LED flash, [3] horn chirps etc.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
Press
Transmitter
Button One Chirp / LED one pulse
Factory Default Setting
Two Chirps / LED two pulse Three Chirps / LED three
pulse
1
Chirps on Chirps off
2
Pathway illumination feature
“off” Parking light “on” for 30-
second upon an unlock
signal
Parking light “on” for 30-
second upon an unlock
signal & 10-second upon a
lock signal.
3 H5/4 Pink Wire = 2-Step
Door Unlock Output H5/4 Pink Wire = Factory
Security Disarm Signal
Output H5/4 Pink Wire = Start
Status (Shock Sensor
Bypass Control) Output
4 H2/4 Brown Wire = Horn
Output
H2/4 Brown Wire = Channel
4 Output H2/4 Brown Wire = Rearm
Signal Outpu
t
5
+
H5/3 White Wire = Dome
Light Output H5/3 White Wire = Channel
4 Output H5/3 White Wire = Ground
Output During Start (Crank)
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Ground Output During Start (Crank) = This wire will provide a 200mA ground output while the starter
output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire
found in some GM vehicles. This wire is also referred to as the ECM wake up wire in some vehicles.
ALARM FEATURE “
II
” PRORAMMING:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch
4 times and holding in on the 4
th
push until two chirps with a long chirp is hearing
and the LED start to flash then release the valet switch. You are now in the Alarm feature ‘II’
programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
0.8-second Door
lock pulses. 3.5-second Door
lock pulse. Double pulse unlock Door lock with
“Comfort Feature”
2
Ignition controlled
door locks & unlocks Ignition controlled
door locks only Ignition controlled
door unlocks only Without ignition
controlled door locks
& unlocks
3
Door lock before
start Door lock after
shut-down Door lock before
start and Door lock
after shut-down Without this feature
4
H6/1 Green Wire =
1 Pulse Remote
Start H6/1 Green Wire =
3 Pulse Remote
Start
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Comfort Feature:
MEGA 250 INSTALL 12