Media5 Mediatrix Sentinel Скачать руководство пользователя

Страница: 32 / 35

Hardware Installation Guide - Mediatrix Sentinel

Standards Compliance and Disclaimers

Supported Standards

The standards compliance of the Mediatrix units are printed on the same sticker as the product serial

number. Refer to

Sticker

Category

Specification

Agency approvals

• European Union
• CE mark (Declaration of Conformity)
• UL mark
• FCC

Safety standards

• UL 60950-1, 2nd Edition, 2011-12-19
• CAN/CSA-C22.2 No. 60950-1- 07 2nd Edition,

2007

• IEC 60950-1 :2005 (2nd edition); Am1 : 2009 with

all national deviations

• CSA C22.2 No. 60950-1-07 + Am1 :2011
• EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011

Emissions

• EN61000-3-2 : 2006 + A1:2009 + A2:2009
• EN61000-3-3 : 2008
• FCC part 15 (2013) subpart B, Class A
• EN55022 (2010), class A

Immunity

EN55022 :2010
• EN61000-4-2 :2009
• EN61000-4-3 :2006 + A1:2008 + A2:2010
• EN61000-4-4 :2004 + A1:2010
• EN61000-4-5 :2006
• EN61000-4-6 :2009
• EN61000-4-11 :2004

Telecom

• TBR 4 (ISDN PRI) (10/21/2013, modified) – In

progress

• CS-03 Part I; Issue 9 including Amendment 1 to 3

- Approbation number 3192A-087, REN is 0.1

• CS-03 Part VI; Issue 9 including Amendment 1 -

Approbation number 3192A-096

• ANSI/TIA-968-B, August 11, 2009, TIA-968-B-1:

2012

Содержание Mediatrix Sentinel



































Результаты поиска

Содержание Mediatrix Sentinel

Отзывы:

Похожие инструкции для Mediatrix Sentinel

Бренды по названию

Популярные бренды

Media5 Mediatrix Sentinel, Руководство по установке оборудования

Результаты поиска

Содержание Mediatrix Sentinel

Отзывы:

Похожие инструкции для Mediatrix Sentinel

Бренды по названию

Популярные бренды