Mec 34-J Diesel, Руководство по обслуживанию и запасным частям

Страница: 117 / 272

Page 111 34-J Desel - Servce & Parts Manual
December 2021 Secton 19 - Troubleshootng
Problem Possible Cause Remedy/Solution
Boom Extend/Retract
No boom extension
Excessive weight on platform Reduce weight to within platform capacity
Level sensor out of level (platform
elevated above 10’) Indicator light will be illuminated and alarm will sound off.
Reposition machine to level ground
Main relief valve (25) out of
adjustment Adjust Main relief valve (25) to rated platform capacity located on function
manifold - see Hydraulic Section.
Solenoid Valve (8) (dump valve) not
energized
Check wiring to valve. Check EZ-Cal ref. P5-7 for output
Ext/Retract valve (10) not energized Check wiring to valve. Check for EZ-Cal message or flash code.
Extend/Retract valve (10) not
shifting
Clean debris. Check for damage/replace.
Ext/Retract switch inoperative
Check switch output using EZ-Cal ref. 2D-2, P14-1 & P14-2 for upper
control digital output signal
Battery discharged - no charge
output Check battery voltage, alternator output (14.5 volts). Check GP500 for 4-4
flash code.
System interlock Check EZ-Cal HELP messages for interlock
Boom extends/retracts
slow
Excessive weight on Platform Reduce weight to within platform capacity
Main relief valve (25) out of
adjustment Adjust Extend relief valve (see Hydraulics Section) located on function
manifold.
Extend/Retract valve (10) not
shifting completely
Clean debris. Check for damage/replace.
Extend Speed adjustment reduced
in GP500 Processor Use the EZ-Cal and check/adjust setting.
See ADJUSTMENTS/TELESCOPE OUT MAX
No boom retract
Main relief valve (25) out of
adjustment Adjust Main relief valve (25) to rated platform capacity located on function
manifold - see Hydraulic Section.
Foreign debris stuck in boom slide
pads
Inspect/clean slide pads.
Solenoid Valve (8) (dump valve) not
energized
Check wiring to valve. Check EZ-Cal ref. P5-7 for output.
Ext/Retract valve (10) not energized Check wiring to lift valve. Check for EZ-Cal message or flash code.
Extend/Retract valve (10) not
shifting
Clean debris. Check for damage/replace.
Ext/Retract joystick inoperative
Check joystick output using EZ-Cal ref. 2D-2, P14-1 & P14-2 for upper
control analog output signal.
Battery discharged - no charge
output Check battery voltage, alternator output (14.5 volts). Check GP500 for 4-4
flash code.
System interlock Check EZ-Cal HELP messages for interlock
Problem Possible Cause Remedy/Solution
Platform Auto-Level
Platform will not remain
level while elevating or
lowering platform (level
cylinder not moving at all)
Platform Level solenoid (4.1) valve
not energized Check wiring to valve. Check output from GP500 P5-10 (UP) and P5-11
(DOWN).
Platform Level solenoid valve (4.1)
sticking Remove valve and inspect for debris or damage. Replace valve located
up on the side of the boom.
Counterbalance valve faulty Valve must not be tampered with. Replace valve.
Flow Compensator valve (2) not
shifting
Clean debris. Check for damage/replace.
Platform will not remain
level while elevating or
lowering platform (level
cylinder moving too slow
or fast)
Excessive weight on Platform Reduce weight to within platform capacity
Main relief valve (25) out of
adjustment Adjust main relief valve (see Hydraulics Section) located on function
manifold.
Platform Level solenoid valve (4.1)
not shifting completely
Clean debris. Check for damage/replace.