manualshive.com logo in svg

Mec 13500001, Руководство оператора, Страница: 25 / 44

Поделиться
Скачать
Mec 13500001 Скачать руководство пользователя страница 25

93075 

Page 23

4069 RT

April 2014

4069 RT

Operating Instructions & Function Tests 

Optional Centered Platform

Machines equipped with the optional Centered Platform are not equipped with a sheet 
materials rack. DO NOT use the optional Material Clamps/Pipe Racks or mount materials 
outside the platform. 

Optional Material Clamps/Pipe Racks

The Material Clamps/Pipe Racks may be used only on the Sheet Material Rack side of the platform.
DO NOT use on the side opposite the Sheet Material Rack.
All material must be centered.

The optional Material Clamp/Pipe Rack allows the user to hold sheet material in place without 
the use of straps, or by inverting the clamps, to carry pipe or other long material.

Mount the clamps approximately 8 inches (20 cm) from the ends of the materials, above the 
Sheet Material Rack. Move the clamps closer together as needed to enable the use of both 
clamps on shorter material.

Material Clamp Use

Remove the J-shaped arms from the Material Clamps when loading material on the Sheet 
Material Rack. 

When all material is loaded, replace the J-shaped arms as shown and secure them in place with 
the snap pins.

ART_4279

Содержание 13500001













































Отзывы:

Нет отзывов