background image

—Specifications—

4069 RT

Working Height*

46 ft

14 m

Platform Height

40 ft

12.0 m

Maximum Drive Height

40 ft

12.0 m

Stowed Height 

Top Guardrail

95.5 in.

2.43 m

 Rails Folded

64 in.

1.63 m

Platform Floor

51 in.

1.3 m

Guardrail Height

43.5 in.

1.11 m

Toeboard Height

6 in.

15 cm

Machine Weight** (Unloaded)

11,500 lb

5,210 kg

Lift Capacity

Total

900 lb

410 kg

Standard platform w/

Platform

600 lb

274 kg

Sheet Materials Rack

Sheet Material Rack

300 lb

136 kg

Lift Capacity -- Optional centered platform 

w/ no Sheet Materials Rack

882 lb

400 kg

Deck Extension Capacity

1 Person / 250 lb (113 kg)

Maximum Occupants

2

Length-Stowed (Overall)

126 in.

3.2 m

Length-Stowed (Without Step)

125 in.

3.18 m

Platform Length (Extended)

166 in.

4.22 m

Platform Length (Retracted)

118 in.

3 m

Width (Overall)

69 in.

1.75 m

Platform Width (Outside)

59 in.

1.5 cm

Sheet Rack Width††

7 in.

18 cm

Wheel Base

94.5 in

2.4 m

Turning Radius--Inside

79 in.

2 m

Ground Clearance

10 in

25 cm

Drive Speed (Proportional)

Platform Stowed

0-3.4 mph

0-5.5 km/h

Platform Elevated†

0-.5 mph max.†

0-.8 km/h max.†

Gradability

40%/21.8°

Breakover Angle

42%/23°

Optional Outrigger Range Of Motion

10° side to side

Maximum Ground Pressure, Wheel

123 psi

8.6 kg/cm

2

Maximum Ground Pressure, Outrigger Pad

56 psi

3.9 kg/cm

2

Maximum 
Vibration

does not 

exceed 

2.5 m/sec

2

 

at operator’s 

position

Maximum Wheel Load

3540 lb

1605 kg

Maximum Operating Wind Speed

28 mph / 12.5 m/sec (45 km/h)

Tire Size

26" x 12" / 66 cm x 33 cm

Tire Pressure

Foam-filled

Ambient 
Operating 
Range

-30° C 

minimum; 

50° C 

maximum

Wheel Bolt Torque

55 ft/lb

74.6 Nm

Hydraulic Pressure

Drive System

3500 psi/ 240 bar

Lift System

3200 psi / 220 bar

Hydraulic Fluid Capacity

14 gal / 53 liter

Sound 
Pressure At 
Workstation

80 dB(A)

System Voltage

12 Volt DC

Fuel Capacity

15 gal/ 57 liter

Battery

Type 31 1000CCA

Sound Power 
Level

86 dB @ 1m

Engine

Kubota D1105 Diesel 24.8 HP Tier 4

Meets requirements of CE EN280:2001 + A2:2009 and Australian Standard AS/NZS1418.10:2011. *Working Height adds 6 feet (2 

m) to platform height. **Weight may increase with certain options.
†Drive speed while elevated is inversely proportional to platform height; the higher the platform is, the lower the maximum 
elevated drive speed. The machine is driveable at full height. ††Not applicable to machines with optional Centered Platform.

Содержание 13500001













































Отзывы: