Meatest M631 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 70

background image

M631 Precision RTD Simulator

MEATEST

53

Operation manual

:STATus:OPERation:PTRansition

Syntax:

:STATus:OPERation:PTRansition <DNPD>

:STATus:OPERation:PTRansition?

Description:

This command allows set Operation Positive Transition Register. It is a decimal value
which corresponds to the binary-weighted sum of all bits set in the register. Setting a bit
in the positive transition filter shall cause a 0 to 1 transition in the corresponding bit of the
associated condition register to cause a 1 to be written in the associated bit of the
corresponding event register.

Parameters:

<DNPD>

Operation Positive Transition Register, Range 0 … 32767

Remarks:

Overlapped command

Example:

STAT:OPER:PTR 1.0

STAT:OPER:PTR? Response: 1.00

:STATus:QUEStionable:CONDition

Syntax:

:STATus:QUEStionable:CONDition?

Description:

This  query  returns  the  content  of  Questionable  Condition  register.  It  is  a  decimal  value
which  corresponds  to  the  binary-weighted  sum  of  all bits  in  the  register.  Register  is  not
cleared  after  this  query. The  response to the  query therefore  represents  an  instantaneous
'Snapshot' of the register state, at the time that the query was accepted.

Parameters:

<DNPD>

Questionable Condition register

Remarks:

Overlapped command

Example:

STAT:QUES:COND? Response: 2

:STATus:QUEStionable:ENABle

Syntax:

:STATus:QUEStionable:ENABle <DNPD>

:STATus:QUEStionable:ENABle?

Description:

This command enables bits in the Questionable Data Enable register. Selected bits are
summarized at bit 3 (QSS) of the IEEE488.2 Status Byte register.

Parameters:

<DNPD>

Questionable Data Enable register

Remarks:

Overlapped command

Example:

STAT:QUES:ENAB 2

STAT:QUES:ENAB? Response: 2

«
...
51
52
53
54
55
...
»

Содержание M631







































































Отзывы:

Нет отзывов

Похожие инструкции для M631

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды