Meatest M631 Скачать руководство пользователя страница 44

Страница: 44 / 70

MEATEST

M631 Precision RTD Simulator

Operation manual

[:SOURce]:PLATinum:STANdard <CPD>

[:SOURce]:PLATinum:STANdard?

Description:

This command selects Platinum temperature standard.

Parameters:

<CPD>

{PT385A|PT385B|PT3916|PT3926|USER} (default PT385A)

·PT385A

Pt385 (68) standard

·PT385B

Pt385 (90) standard

·PT3916

Pt3916 standard

·PT3926

Pt3926 standard

·USER

User (see PLAT:COEF command)

Remarks:

Overlapped command

Value is set according to “Startup” preset on restart and to default on *RST command

Example:

PLAT:STAN PT385A

PLAT:STAN? Response: PT385A

[:SOURce]:PLATinum:ZRESistance

Syntax:

[:SOURce]:PLATinum:ZRESistance <DNPD>[<UNIT>]

[:SOURce]:PLATinum:ZRESistance?

Description:

This command sets resistance at 0 °C for Platinum function.

Parameters:

<DNPD>

Range 100.0 ... 1000.0 (default 100.0).

<UNIT>

{OHM}

·OHM

Remarks:

Overlapped command

Value is set according to “Startup” preset on restart and to default on *RST command

Example:

PLAT:ZRES 100.0

PLAT:ZRES? Response: 1.02 OHM

[:SOURce]:RESistance[:AMPLitude]

Syntax:

[:SOURce]:RESistance[:AMPLitude] <DNPD>[<UNIT>]

[:SOURce]:RESistance[:AMPLitude]?

Description:

This command sets amplitude in Resistance mode. Node SOUR:RES also selects
“RESISTANCE” function if not already selected. Optionally unit can be enclosed.

Parameters:

<DNPD>

Range 16.0 ... 400.0e3, default 100.0

<UNIT>

{OHM}

·OHM

Remarks:

Overlapped command

Value is set according to “Startup” preset on restart and to default on *RST command

Example:

RES 100.0

RES? Response: 1.02 OHM

[:SOURce]:TIMing:PCOunt?

Syntax:

[:SOURce]:TIMing:PCOunt?

Description:

Содержание M631







































































Результаты поиска

Содержание M631

Отзывы:

Бренды по названию

Популярные бренды

Meatest M631, Руководство по эксплуатации

Результаты поиска

Содержание M631

Отзывы:

Бренды по названию

Популярные бренды