background image

Security

Use the web interface to set the level of access to the website and to change the administrator password.

High: access to the web page requires a password.
Medium: access to the web page is permi ed for any user, and data can be read by any user, but changes

to the device configura on or files require a password.
Off: full access is permi ed for all users; no password is required.

By default, security access is set to "Off", and the administrator password is set to "admin". To change the

security level or password, open the web interface and go to the Device window, Security tab. Use the device

Reset bu on to restore security se ngs to factory default values.

Restoring factory default se ngs

To restore network configura on and security se ngs to the factory default values, use a paper clip to press

the CONFIG RESET bu on. When pressed, the default network and security se ngs are wri en to the device

and the WebDAQ is rebooted.

Factory default se ngs

Parameter

Specifica on

IP address

192.168.0.101

subnet mask

255.255.255.0

Gateway

192.168.0.1

DHCP se ng

DHCP + link-local enabled

Security level

Off

Password for the admin

account

admin (case-sensi ve)

Password for the share

account

share (case-sensi ve)

Device name

webdaq-xxxxxx, where xxxxxx is the last 6 digits of the MAC address

(printed on the label on the underside of the device).

The network se ngs, security level, user account passwords and device name can be changed with the

WebDAQ web interface.

When factory defaults are restored, any shared folders or mapped drives are reset.

Contents

WebDAQ 504 User's Guide

page 8

Содержание WebDAQ 504






























Отзывы: