background image

Where to find more informa on

Addi onal informa on about the WebDAQ Series of internet enabled data loggers is available on our website at

www.mccdaq.com/WebDAQ

. You can also contact Measurement Compu ng Corpora on with specific

ques ons.

WebDAQ web interface: Open the Help window for informa on about using WebDAQ so ware.
Knowledgebase: 

kb.mccdaq.com

WiFi adapters approved for use with WebDAQ Series hardware: 

www.mccdaq.com/pdfs/manuals/wd-

wifi.pdf

Tech support form: 

www.mccdaq.com/support/support_form.aspx

Email: 

[email protected]

Phone: 508-946-5100 and follow the instruc ons for reaching Tech Support

For interna onal customers, contact your local distributor. Refer to the Interna onal Distributors sec on on our

website a

www.mccdaq.com/Interna onal

.

 

 Hazardous voltages

Take the following precau ons if you connect hazardous voltages to the WebDAQ 504. A hazardous voltage is a

voltage greater than 42.4 Vpk or 60 VDC to earth ground.

Ensure that hazardous voltage wiring is performed only by qualified personnel adhering to local electrical

standards.
Do not mix hazardous voltage circuits and human-accessible circuits on the same device.
Make sure that devices and circuits connected to the WebDAQ are properly insulated from human

contact.

Hazardous loca ons: The WebDAQ is not cer fied for use in hazardous loca ons.

Contents

WebDAQ 504 User's Guide

page 2

Содержание WebDAQ 504






























Отзывы: