McQuay RoofPak RDS 802C Скачать руководство пользователя страница 23

Страница: 23 / 62

Page 22 / IM 178

Step 2

Remove gasketing around door flange and save for use on
vestibule. See Step 4. Remove door and save for Step 4.

Figure 16b.

Step 4

1. Reassemble access door to vestibule by screwing hinges

into side panel using screws saved from Step 1. (Access
door must be attached to the vestibule in the same
opening direction as it was on the unit.)

2. Remove and discard latch handle locking screws and

retaining washer. Fasten door latch assembly to side
panel using screws and bushing saved from Step 1.
(Latch must be fastened on the same side as when
located on the unit.)

3. Fasten upright angles to vestibule using #10 screws

supplied.

4. Seal between unit and vestibule with silicone sealant

along top and sides as shown.

Note: Any holes cut in the floor of the unit must be sealed to
prevent water leakage.

Figure 16d.

Step 3

1. Assemble side panels A and B to uprights using #10 drill

screws supplied. Make certain side panels are flush
against uprights before securing into place.

2. Fasten bottom panel D to base channel using #10 drill

screws and to side panels A and B using #10 screws
supplied.

3. Set top panel C in place and fasten to side panels A and

B using #10 screws and to top panel using #10 screws
supplied.

Figure 16c.

#10 Screw

#10 Drill
Screw

#10 Screw

#10 Drill
Screw

Silicone
Sealant

Upright

Angle

#10

Screw

Door Latch Assembly
(See Step 2)

Gasketing

Door

Door Prop

Upright Angle

Gasketing

Door Prop

Gasketing

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание RoofPak RDS 802C































































Результаты поиска

Содержание RoofPak RDS 802C

Отзывы:

Похожие инструкции для RoofPak RDS 802C

Бренды по названию

Популярные бренды

McQuay RoofPak RDS 802C, Установка и обслуживание данных

Результаты поиска

Содержание RoofPak RDS 802C

Отзывы:

Похожие инструкции для RoofPak RDS 802C

Бренды по названию

Популярные бренды