McLaughlin VERSA-MOLE McL-10H Скачать руководство пользователя страница 40

Страница: 40 / 47

STEP 12: CHAIN GUARD INSTALLATION

51. Clean oﬀ any remaining silicone from the edges

of the chain guard and from the back side of the
carriage plate.

52. Apply two (2) thin beads of silicone sealant (Dow

Corning-RTV # 732, or equivalent) to the inner
edge and outer edge of the chain guard.

53. Press the chain guard to the back of the carriage

plate and wiggle slightly to ensure proper seating
of the sealant. Install the seven (7) screws which
hold it to the carriage back plate.

STEP 13: SWIVEL INSTALLATION

53. Apply a light bead of removable pipe sealant to the

male threads of the swivel and screw it into the end
of the spindle.

54. Reconnect the water supply hose.

STEP 14: CHUCK INSTALLATION

55. Place an o-ring in the groove on the face of the

chuck (threaded chuck only).

56. Slide the chuck lockout ring to the front of the

ﬂ ange.

57. Install the ﬁ ve (5) screws through the lockout ring

and chuck ﬂ ange.

58. Line-up the screws and tighten the chuck to the

spindle.

59. Bend down one tab of the lockout ring onto the ﬂ at

portion of each screw head.

SECTION 2: FRAME DISASSEMBLY
& ASSEMBLY
DISASSEMBLY

STEP 1: SIDE SHEET REMOVAL

1. Remove all R-Clip pins which hold the side sheets

in place.

2. Pull the side sheets out and up to remove them.

STEP 2: CONVEYOR BELT REMOVAL

3. Remove all nuts holding the conveyor support

sheets against the conveyor.

4. Remove the side sheet.
5. Remove the two (2) machine screws at each end of

the conveyor belt.

6. Remove the conveyor belt.

STEP 3: THRUST CHAIN REMOVAL

7. Loosen the nut on the bottom of the chain tension-

er.

8. Locate the chain turnbuckle.
9. Use a screwdriver to rotate the turnbuckle. Place

the screwdriver in the most accessible hole and
rotate the turnbuckle. Rotate clockwise or counter-
clockwise to determine if the chain is getting tight

9.4.0

Содержание VERSA-MOLE McL-10H
















































Результаты поиска

Содержание VERSA-MOLE McL-10H

Отзывы:

Похожие инструкции для VERSA-MOLE McL-10H

Бренды по названию

Популярные бренды

McLaughlin VERSA-MOLE McL-10H, Компоненты и руководство по ремонту

Результаты поиска

Содержание VERSA-MOLE McL-10H

Отзывы:

Похожие инструкции для VERSA-MOLE McL-10H

Бренды по названию

Популярные бренды