background image

8

Connections on the Back

The Inputs

Seven HDMI Inputs (six 4K, one 8K)
One pair balanced XLR Inputs (AES/EBU)
Eight pairs RCA analog stereo Inputs including one 

MM (moving magnet) RCA stereo pair and ground 

connection
Two coaxial digital audio Inputs
Two Toslink optical Inputs
Four RCA video Inputs
Three sets of three component video RCA jacks 
One 7.1 CH Input with eight analog RCA jacks
One USB port to supply power
One USB port to connect storage
One 10baseT LAN connector

Figure 03–  MX123 Rear View

One 1/8 inch jack for microphone Input 
One 1/8 inch jack for RS232 connector
One 1/8 inch jack for wired IR Input
One AC power connector

The Outputs

Three HDMI Outputs (Two MON 8K, ZONE 2 4K) 
15 balanced XLR audio Outputs
17 unbalanced RCA Outputs
Two 1/8 inch jack Power Control (trigger) Outputs
Two RCA stereo pairs Output to two additional 

zones
One set of three component video RCA Outputs
Two RCA video Outputs
One 1/8 inch Data Output jack

Making Connections

• Do not plug in the power cord until  

all connections have been completed.

Bluetooth/Wi-Fi Antenna

Attach the two Bluetooth/Wi-Fi antennas that 

are included in the MX123 accessory package. 

Each antenna screws into a connector labeled 

BLUETOOTH/WI-FI ANT located in the top right 

and left corners of the rear panel. After attaching the 

antennas, point them upward. 

10baseT LAN

Use an Ethernet cable to connect the MX123 to a 

network router. The network connector is located 

on the top left rear of the MX123. It is labeled 

NETWORK. By default, the MX123 has DHCP set 

to ON and will automatically receive an IP address 

from the router. This setting can be changed. (See 

“Network” on page 24.)

3 (BLU-RAY)

4 (GAME)

5 (MEDIA PLAYER)

6 (CD)

ZONE 2 (4K)

MON 1 (8K)

2 (DVD)

Y

PB

PR

Y

FR

SUB

SR

SBR

HDMI IN

VIDEO

IN 2 (DVD)

IN 3 (BLU-RAY)

PB

PR

Y

PB

PR

XLR BALANCED INPUT

R

L

FR

FL

C

SW1

SR

SL

SBR

SBL

BALANCED OUTPUTS

SW2

1 (CBL/SAT)

2 (DVD)

3 (BR)

4 (GAME)

Z2 OUT

MON OUT

IN 1 (CBL/SAT)

COMPONENT VIDEO

MONITOR OUT

ANALOG AUDIO OUT

ZONE 2

ZONE 3

L

R

FR

SW1

SR

SBR

SW2

HR1

HR2

FL

C

SL

SBL

7.1 CH INPUT

UNBALANCED PRE OUT

FL

C

SL

SBL

HL1

HL2

TUNER

CBL/SAT

DVD

BLU-RAY

GAME

ANALOG AUDIO IN

L

R

PHONO

HR1

HL1

HR2

HL2

GND

2

(CD)

OPT

A/V PROCESSOR

MX123

MCINTOSH LABORATORY, INC.,

BINGHAMTON, NY

HANDCRAFTED IN USA WITH US AND IMPORTED PARTS

HR3

HL3

1 (CBL/SAT)

7 (AUX 8K)

ARC

COAX

1

(TV AUDIO)

RS232

TRIG 1

IR IN

DATA

OUT

SETUP

MIC

TRIG 2

CD

MP

HDMI OUT

MON 2 (8K)

1

2

3

4

5

6

CAN ICES-3(B)/NMB-3(B)

1

2

HL4/WIDE

HR4/WIDE

HR3

HL3

DIGITAL AUDIO IN

(CBL/SAT)

(DVD)

NETWORK

POWER SUPPLY

5V/1.5A

      USB

5V/1A

BLUETOOTH

/ Wi-Fi ANT

BLUETOOTH

/ Wi-Fi ANT

SERIAL

NUMBER

      

75 WATTS

120V      

      

50 60Hz

FOR INDOOR

USE ONLY

eARC

Содержание MX123





































Отзывы: