McElroy DynaMc 28 Скачать руководство пользователя

Страница: 5 / 50

Table of Contents

Safety

Safety Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Read and Understand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Wear Safety Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Heater is Not Explosion Proof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Electric Motors are Not Explosion Proof . . . . . . . . . . . . . . . . . . . . . . . 1-2

Pipe Handling Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Units with Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Crush Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Facer Blades are Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Have Tires Properly Serviced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Do not Tow Fusion Machine at Speeds Greater than 5 MPH . . . . . . . . . 1-5

Heater is Hot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Fusion Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Positioning Fusion Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Overview

Theory of Heat Fusion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Introduction to the 28 and 412 Hand Pump Fusion Machines . . . . . . . . 2-2

Carriage Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Oil Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Hydraulic Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Facer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Heater Stripper Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Insulated Heater Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Pipe Lifts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Clamp Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

McELROY MANUFACTURING, INC.

Tulsa, Oklahoma, USA

All product names or trademarks are property of their respective owners. All information,

illustrations and specifications in this manual are based on the latest information available

at the time of publication. The right is reserved to make changes at any time without notice.

Содержание DynaMc 28



















































Результаты поиска

Содержание DynaMc 28

Отзывы:

Похожие инструкции для DynaMc 28

Бренды по названию

Популярные бренды

McElroy DynaMc 28, Руководство оператора

Результаты поиска

Содержание DynaMc 28

Отзывы:

Похожие инструкции для DynaMc 28

Бренды по названию

Популярные бренды