McElroy DynaMc 28 Скачать руководство пользователя

Страница: 12 / 50

Safety

1 - 5

Have Tires Properly Serviced

Failure to follow proper procedures when

mounting a tire on a wheel or rim can produce

an explosion which may result in serious injury

or death. Have tires mounted by someone that is

experienced, and has the proper equipment to

perform the job safety.

TX00118-4-22-93

WR000

-4

-2

Do Not Tow Fusion Machine at Speeds Greater

than 5 MPH

The chassis is not designed for over-road towing.

Towing at speeds greater than five miles per hour

can result in machine damage as well as injury.

Always transport the machine by flatbed truck or

similar means, and make sure that unit is properly

secured.

TX00101-4-12-93

CD0018

9-1-

-9

Fusion Procedures

Obtain a copy of the pipe manufacturer's procedures or

appropriate joining standard for the pipe being fused. Follow the

procedure carefully, and adhere to all specified parameters.

NOTICE:

Failure to follow pipe manufacturer's procedure

could result in a bad joint. Always follow pipe

manufacturer's procedures.

TX04469-10-24-12

WR000

79-1-

-9

Heater Is Hot

The heater is hot and will burn clothing and skin.

Keep the heater in its insulated heater stand or

blanket when not in use, and use care when

heating the pipe.

NOTICE

: Use only a clean non-synthetic cloth to clean the heater

plates.

TX00104-01-03-14

WR000

-2

-10

-9

Содержание DynaMc 28



















































Результаты поиска

Содержание DynaMc 28

Отзывы:

Похожие инструкции для DynaMc 28

Бренды по названию

Популярные бренды

McElroy DynaMc 28, Руководство оператора

Результаты поиска

Содержание DynaMc 28

Отзывы:

Похожие инструкции для DynaMc 28

Бренды по названию

Популярные бренды