manualshive.com logo in svg

McCrometer ML255, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
McCrometer ML255 Скачать руководство пользователя страница 9

BATTERY INSTALLATION AND SYSTEM START-UP

Copyright © 2018 McCrometer, Inc. All printed material should not be changed or altered without permission of McCrometer. 

Any published technical data and instructions are subject to change without notice. Contact your McCrometer representative 

for current technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA 

Printed In The U.S.A.

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078 

Lit. # 30122-46 Rev. 1.2 / 5-31-18

7

3.4 

Replacing Batteries

Contact your local McCrometer representative or McCrometer Customer Service (customerservice@mccrometer.

com) to order replacement batteries.

1.  Power down the system.

a.  If there is external power applied to the converter, unplug it.
b.  Press the 

Enter/Esc

 button for one second to turn on the front panel display.

c.  Press the 

Enter/Esc

 button again to display the menus.

d.  Select 

Main Menu 

and press 

Enter

.

e.  Enter the L2 access code.
f.  Navigate to menu 

10-Diagnostic

 and press 

Enter

.

g.  Select 

Stand-By

 and press 

Enter

.

h.  Long press 

Enter 

to execute. The display will indicate "

Stand-By" 

momentarily and then go blank.

i.  Move battery DIP switch B1/B2 to OFF.

The unit is now safely powered down.

2. 

Remove the batteries.

a.  Disconnect the battery connectors from the B1 and B2 sockets on the Main Board.
b.  Remove the two screws securing the battery holder to the converter housing.
c.  Remove the holder from the converter.

3. 

Installing Batteries:

a.  Remove the battery holder from the ML255 converter by removing the two screws and lock washers 

holding it in place.

b.  Cut the tie wraps from the batteries and dispose of the battery packs.
c.  Secure new battery packs to the battery holder using tie wraps.
d.  Re-install the battery holder into the converter using the previously removed screws and washers.
e.  Plug the battery pack connectors into the B1 and B2 sockets on the main board.

4.  Power up the system.

a.  Wait one minute after plugging in the battery pack connectors.
b.  Move battery DIP switch B1/B2 to ON.
c.  The converter will begin powering up and the red CPU LED will turn on solid. It will then begin flashing 

after it completes booting.

Note: Powering up may take two to three minutes.

Содержание ML255



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды