McCrometer ML255 Скачать руководство пользователя страница 39

Страница: 39 / 50

MAIN MENU DESCRIPTIONS

Any published technical data and instructions are subject to change without notice. Contact your McCrometer representative

for current technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA

Printed In The U.S.A.

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078

Lit. # 30122-46 Rev. 1.2 / 5-31-18

Load fact.data

This will configure the converter to the configuration when it left McCrometer.

S/n

Displays the board serial number.

Used to adjust gain errors. This factor is generated by the converter at power up.

Field adjustment coefficient. This value is a direct multiplier that is used as a field adjustment / correction coefficient.

CAUTION

if the passcode is changed from the default value and is lost, it CANNOT be recovered. In

the event the passcode is lost, the converter can be returned to the factory to be reset.

9.11 Menu 11 - Internal Data

L2 code

Level 2 passcode. This menu changes the 2 level passcode. The factory default

is 000002.

 

 



 

















Содержание ML255



















































Результаты поиска

Содержание ML255

Отзывы:

Бренды по названию

Популярные бренды

McCrometer ML255, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ML255

Отзывы:

Бренды по названию

Популярные бренды