McCrometer ML255 Скачать руководство пользователя страница 6

Страница: 6 / 50

CONVERTER INSTALLATION

Any published technical data and instructions are subject to change without notice. Contact your McCrometer representative

for current technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA

Printed In The U.S.A.

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078

Lit. # 30122-46 Rev. 1.2 / 5-31-18

2.0

CONVERTER INSTALLATION

2.1

Mounting The Converter

If possible mount the converter in an electronics shed or environmental enclosure. If the converter is mounted

outdoors a sun shield is recommended. The sun shield should be oriented in a direction to reduce sun damage

and ensure readability. The converter is mounted using 2 bolts.

See Figure 1

. A service loop in the cables is

required.

See Section 3.2

. This electronic unit is rated IP67 for temporary flooding.

2.2

Installing Cables To Converter And Service Loop

Conduit of any kind

CANNOT

be attached directly to the electronics enclosure. Attaching conduit directly to the

enclosure will introduce dangerous gasses and moisture into the enclosure creating a dangerous condition, and

will remove the enclosure's IP67 rating.

Attaching conduit to the enclosure or altering the enclosure in any

way will void the warranty.

Any cable running through a conduit must exit the conduit and have a minimum of an 8" service loop before

entering the electronics enclosure through the cable glands. All cable compression glands must be properly

tightened to prevent moisture intrusion and maintain the IP67 rating. This allows the electronics enclosure to be

rotated and the rear panel to be accessed. If electrically bonding (grounding) the enclosure to metallic conduit

or raceways, secure a lead wire to the enclosures back panel screw and attach the lead to a listed and approved

conduit grounding bushing. See

Figure 3

. To insure IP67 rating use only round cable 0.125" to 0.375" in diameter.

Figure 3.

Cable Installation, A Service Loop And Bonding To Metallic Conduit

WARNING:

Do not connect any form of conduit directly to the converter enclosure. Doing so will allow

moisture and potentially dangerous gasses to enter directly into the converter. Attaching any conduit to

the enclosure, or altering the enclosure in any way will void the warranty.

Grounding Lead

Sensor Cables

(Showing 8”

Service Loop)

Power Cable

Conduit Grounding

Bushings

Enclosure Front

Enclosure Back

Enclosure

Backplate

Screw

IMPORTANT

: All cables must have a minimum 8" service loop.

Содержание ML255



















































Результаты поиска

Содержание ML255

Отзывы:

Бренды по названию

Популярные бренды

McCrometer ML255, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ML255

Отзывы:

Бренды по названию

Популярные бренды