MC Electronics AREA CONTROL MCK 3000 Скачать руководство пользователя страница 24

Страница: 24 / 28

MCK 3000

Installation and use

MCK 3000

8. Troubleshooting

In case of appliance malfunctioning, perform the simple checks below to find out what
you need to do.
If the problem still remains after carrying out the suggested checks, contact your local
dealer or

MC elettronica

Technical Service.

PROBLEM

CAUSE

SOLUTION

NITOR

The Monitor does not
turn on

a. The power cable

is disconnected

a. Check the power cable

SENS

The speed sensor
does not work

a. Broken cable

b. Calibration

distance too long

Red part of sensor
damaged

a. Restore connection

b. Adjust the calibration

distance as shown in
paragraph 3.2.1

Replace the sensor

Counted area higher
or lower than the
actual one

a. Incorrectly

programmed work
parameters.

a. Set the work

parameters again (see
chapter 5)

b. Damaged speed

sensor cable

b. Replace the speed
sensor

b. Malfunctioning

mechanical
sensor or seed
sensor

c. Replace the mechanical
sensor or the seed sensor

Содержание AREA CONTROL MCK 3000





























Результаты поиска

Содержание AREA CONTROL MCK 3000

Отзывы:

Похожие инструкции для AREA CONTROL MCK 3000

Бренды по названию

Популярные бренды

MC Electronics AREA CONTROL MCK 3000, Инструкции по использованию и сборке

Результаты поиска

Содержание AREA CONTROL MCK 3000

Отзывы:

Похожие инструкции для AREA CONTROL MCK 3000

Бренды по названию

Популярные бренды