Mazda MAZDA5 2006 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

Mazda MAZDA5 2006 Скачать руководство пользователя страница 13

13

1030658 Rev.A 09/05

SYSTEM POWER-UP

1. Verify that all connections are secure as per installation instructions.

2. Turn the ignition key to the RUN position.

3. Reconnect the negative battery terminal.

4. Turn the ignition key to the OFF position.

5. VERY IMPORTANT - USING THE IGNITION KEY, TURN THE IGNITION TO THE ON POSITION THEN

CRANK ENGINE UNTIL IT STARTS ONE TIME THEN SHUT THE VEHICLE OFF.

13

IMMOBILIZER INTERFACE PROGRAMMING

NOTE: IF YOU DID NOT START THE CAR WITH THE IGNITION KEY AS INSTRUCTED TO IN SECTION 13 STEP 5

THEN THE VEHICLE WILL NOT ATTEMPT TO START, INSTEAD YOU WILL GET THREE ADDITIONAL BEEPS FROM

THE HORN. THE VEHICLE HAS TO BE STARTED AT LEAST ONCE WITH THE KEY FOR THE REMOTE ENGINE

START FUNCTION TO OPERATE.

1. Transponder interface programming:

NOTE: Two programmed ignition keys are required for this step and hood must be closed.

a. Sitting in the driver seat, be prepared to press the brake pedal to shut down the remote starter
system.

b. Using the first key, turn the ignition on, wait for the THEFT light to turn off, then turn the ignition off and
remove key from the ignition switch.

c. Using the second key within 5 seconds, turn the ignition on, wait for the THEFT light to turn off, then
turn the ignition off and remove key from the ignition switch.

d. Activate the remote start function by pressing the START button (2) times within 5 seconds.

The system should flash the parking lights and chirp the horn one time, pause for four seconds then
start the engine

.

e. After the engine is started. Press the brake pedal to shutdown the engine. The Immobilizer interface is
now programmed.

f. Attach new Remote Engine Start transmitters to the retractable keys.

15

UNDERHOOD WARNING LABEL MOUNTING

14

1. Open the engine hood and find a suitable mounting location in the engine compartment that will be in plain

sight when the hood is open (on the radiator cowl).

2. Using an alcohol pad, clean the mounting surface thoroughly.

3. Remove the backing on the underhood sticker and mount in place.

4. Close hood.

«
...
11
12
13
14
15
...
»

Содержание MAZDA5 2006





















Отзывы:

Нет отзывов