Maytag MVWB750WR1 Скачать руководство пользователя страница 2

Страница: 2 / 16

W10313093A

FOR SERVICE TECHNICIAN ONLY – DO NOT REMOVE OR DESTROY

POUR LE TECHNICIEN SEULEMENT – NE PAS ENLEVER NI DÉTRUIRE

something is faulty with the button, and it is not
possible to enter the diagnostic mode.

➔

If no indicators come on after pressing POWER/
CANCEL, press any other key, move the cycle
knob, or open the lid and repeat step 1.

Indication 2: Fault code flashes from the
display.
Action:

Review the Display Fault/Error Codes table,

page 3, for the recommended procedure.

DIAGNOSTIC: Saved Fault Codes

The washer will save up to 4 of the most recent
fault codes. Errors are not displayed or saved in
chronological order of appearance. If there are saved
fault codes (as indicated in step 3 of Activation of
Automatic Diagnostic Test Mode, page 1), the fault code
saved in the first memory location will be displayed and
show “F” and “XX” where XX is the fault code.

Press and release

the same button

used to activate

Diagnostics

➔

Second memory location saved
fault code is displayed.

Repeat

➔

Third memory location saved
fault code is displayed.

Repeat

➔

Fourth memory location saved
fault code is displayed.

Repeat

➔

All indicators momentarily turn
off, then stay on. After 5 seconds,
Automatic test cycle begins.

NOTE:

Fault codes are retained, after displaying them

ACTIVATION OF MANUAL DIAGNOSTIC
TEST MODE

Read and perform steps 1 and 2 under
Activation of Automatic Diagnostic Test Mode,
page 1, and press the same button once during
the first 5 seconds of display of the

8:88

NOTE:

If the button is not pressed within 5 seconds,

the Automatic test will start (after saved fault codes).

If done successfully, a single beep occurs and the
three-digit display shows the User Interface ID# (

DIAGNOSTIC: Manual

Enter Manual Diagnostic test mode, above. Three-digit display
shows

000

, and Add A Garment indicator LED is flashing.

NOTE:

If there is no activity (button press, cycle select)

within 5 minutes, the control automatically exits
Diagnostic mode and enters standby mode.

Manual: Water Valves

(See Manual Activation, above)

To check FRESH valve

select and press the following:

WHITES or EXTREME DIRT

➔

START/PAUSE (turns on

Fresh valve, cycle indicator flashes)

➔

WASH TEMP/

RINSE TEMP (selecting hot/cold = hot valve; warm/
warm = hot & cold valve; warm/cold = cold valve)

➔

START/PAUSE (turns off Fresh valve, cycle indicator

is steady on).

To check DETERGENT valve

select or press the following:

SUPER WASH or HEAVY DUTY

➔

START/PAUSE

(turns on Detergent valve, cycle indicator flashes)

➔

WASH TEMP/RINSE TEMP (selecting hot/cold =
hot valve; warm/warm = hot & cold valve; warm/

Detergent valve, cycle indicator is steady on).

To check FABRIC SOFTENER valve

select or press

the following:

NORMAL

➔

START/PAUSE (turns on Fabric Softener

valve, cycle indicator flashes)

➔

WASH TEMP/RINSE TEMP

(selecting hot/cold = hot valve; warm/warm = hot &
cold valve; warm/cold = cold valve)

➔

START/PAUSE

(turns off Fabric Softener valve, cycle indicator is steady on).

To check BLEACH valve

select or press the following:

DARKS AND COLORS or COLORS/TOWELS

➔

START/PAUSE (turns on Bleach valve with cold water,
cycle indicator flashes)

➔

START/PAUSE (turns off

Bleach valve, cycle indicator is steady on).

NOTE:

Washer can only fill cold through Bleach valve.

Manual: Pumps

(See Manual Activation, at left)

Select CLEAN WASHER or DRAIN & SPIN cycle.

Press and release:

START/PAUSE

➔

Turns on recirculation pump,
cycle indicator is steady on.

Repeat

➔

Turns off recirculation pump,
cycle indicator is steady on.

Repeat

➔

Turns on drain pump, cycle
indicator flashes.

Repeat

➔

Turns off drain pump, cycle
indicator is steady on.

➔

If pumps fail to turn on, go to TEST #7, page 6.

Manual: Lid Lock

(See Manual Activation, at left)

NOTE:

Lid must be closed. If lid is not closed, an invalid

button press beep will occur when performing next step.

Press and release:

WATER SAVE

SPRAY RINSE or

REMINDER RESET

➔

Lid locks, Lid Lock indicator
turns on.

Repeat

➔

Lid unlocks, Lid Lock
indicator turns off.

➔

If lid does not lock or unlock, go to TEST #8, page 6.

Manual: Motor

(See Manual Activation, at left)

Rotor Position Sensor (RPS):

Uses Wash, Rinse,

and Spin indicators (if available) to detect the three
hall sensors. Console may have up to two of these
indicators on at one time when the basket is not moving.
Open lid and rotate basket by hand. The Wash, Rinse,
and Spin status indicators should toggle on and off
according to direction the basket is being turned.

➔

If none of these indicators are on, go to TEST #3,
page 4.

Agitate:

Water must cover the wash plate to

ensure the basket is floating prior to agitation.
Enabling agitation without enough water may cause
a fault condition to occur. See Manual: Water Valves
test, at left.

Press and release:

SOIL LEVEL

➔

Gentle wash action.

Repeat

➔

Normal wash action.

Repeat

➔

Heavy wash action.

Repeat

➔

Motor turns off.

NOTE:

Indicators to left of button scroll from right to left.

➔

If motor fails to agitate, go to TEST #3, page 4.

Manual: Heater

(If supplied) (See Manual

Activation, at left)

Water must cover the wash plate to ensure the heater
is completely submerged. Heater will not be enabled if
there is less than 75 mm of water in the washer tub,
and the Cold valve needs to be active:

➔

Press WASH TEMP/RINSE TEMP until selecting
warm/cold.

ACTIVATION OF CONSOLE AND
INDICATORS DIAGNOSTIC TEST MODE

This test checks the cycle selector knob, indicators,
buttons, three-digit display, and beeper.

Plug in washer or reconnect power.

From Standby Mode (plugged in with all indicators
off) or Setting Mode (plugged in and power up just
before running a cycle), press and release (key-dance)
the following buttons within 4 seconds:

SOIL

LEVEL

➔

WASH TEMP/

RINSE TEMP

➔

SOIL

LEVEL

➔

WASH TEMP/

RINSE TEMP

If successful, three digits will display “dt” and you will
have 5 seconds to complete next step.

Within 5 seconds of showing “dt” in display, press
START/PAUSE (all indicators in display are illuminated
and

8:88

is displayed).

➔

Press START/PAUSE a second time. This turns
off the three-digit display and all status indicators
except for the delay indicator (if present). All other

➔

P
status indicators and three-digit display (all indicators
are illuminated).

Rotate WASH CYCLE selector back and forth.
Indicators will toggle on (or off).

Press buttons to verify function. Indicators will toggle
on (or off) and beep tone will sound when buttons
are pressed.

➔

If no indicators come on after that, go to TEST #1,
page 4.

8 1

, etc.) for 3 seconds, then displays

000

and the

Add A Garment indicator LED flashes. See Diagnostic:
Manual, below.

cold = cold valve)

➔

START/PAUSE (turns off

To turn on the Cold Valve:

ress START/PAUSE a third time. This turns on

and/or interrupting power.

To check OXI valve

select or press the following:

HAND WASH

➔

START/PAUSE (turns on

Oxi valve, cycle indicator flashes)

➔

WASH TEMP/RINSE

TEMP (selecting hot/cold = hot valve; warm/warm =
hot & cold valve; warm/cold = cold valve)

➔

START/

PAUSE (turns off Oxi valve, cycle indicator is steady on).

➔

If any valve fails to turn on, go to TEST #2, page 4.

Models without the Oxi dispenser will need to press
WASH TEMP/RINSE TEMP (selecting hot/cold = hot
valve; warm/warm = hot & cold valve; warm/cold =
cold valve), and water fill may be cold, hot, or warm.

indicators remain illuminated.

➔

Press DELAY START [+] or [–]. This turns off the
delay indicator.

➔

Press DELAY START [+] or [–]. This turns on the
delay indicator.

Spin:

To activate Spin, lid must be closed with lid lock

enabled. See Manual: Lid Lock test, at left.

NOTE:

If lid is not closed, an invalid button press

beep will occur when performing next step.

Press and