Maytag Epic MED/GD9600S, Техническое образование

Страница: 22 / 75

2-13
12345
The following kits for close clearance alternate
installations are available for purchase. Please see the
“ Assistance or Service” section of this manual to order.
Over-the-Top Installation:
Part Number 4396028
Periscope Installation (For use with dryer vent to wall vent
mismatch):
Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm)
mismatch
Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)
mismatch
Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)
mismatch
6789788
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
1232456728927383
Select the route that will provide the straightest and most
direct path outdoors.
Plan the installation to use the fewest number of elbows and
turns.
When using elbows or making turns, allow as much room as
possible.
Bend vent gradually to avoid kinking.
Use the fewest 90° turns possible.
123245672892738273878287222848238
4678244572
Use the following Vent system chart to determine type of vent
material and hood combinations acceptable to use.
12345
Do not use vent runs longer than those specified in
the Vent system chart. Exhaust systems longer than those
specified will:
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and
increased energy usage.
The Vent system chart provides venting requirements that will
help to achieve the best drying performance.
2738325843
12345
Side and bottom exhaust installations have a 90 º turn
inside the dryer. To determine maximum exhaust length, add one
90º turn to the chart.
73273325
Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.
Run vent to dryer location. Use the straightest path possible.
See ?Determine vent path? in ?Plan Vent System.? Avoid 90º
turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior
of the vent to secure vent.
73292672
To protect the floor, use a large flat piece of cardboard from
the dryer carton. Place cardboard under the entire back edge
of the dryer.
Firmly grasp the body of the dryer (not the console panel).
Gently lay the dryer on the cardboard. See illustration.
18
8
3!78
8
"#
88$
$
%&8$
$
'&$8
(8#88
64 ft (20 m)
36 ft (11 m) 58 ft (17.7 m)
28 ft (8.5 m)
'&$8
(8#88
54 ft (16.5 m)
31 ft (9.4 m) 48 ft (14.6 m)
23 ft (7 m)
'&$8
(8#88
44 ft (13.4 m)
27 ft (8.2 m) 38 ft (11.6 m)
19 ft (5.8 m)
'&$8
(8#88
35 ft (10.7 m)
25 ft (7.6 m) 29 ft (8.8 m)
17 ft (5.2 m)
) '&$8
(8#88
27 ft (8.2 m)
23 ft (7 m) 21 ft (6.4 m)
15 ft (4.6 m)
1234546
4#988 *8& +,$
-8 8 7878 8 $ $!8
(8 $ 9 8 9. 8 /!