MAYSER 1006747 Скачать руководство пользователя страница 21

121022 v1.02-RiA 

Operating instructions SG-RS 309-2 

Page 21/23

Replacement parts

The control units produced by Mayser are professional electronic tools exclusive-
ly intended for commercial use (known as B2B devices). Unlike the B2C (busi-
ness-to-consumer) devices mainly used in private households, they must not be 
disposed of at the collection centres of public waste management organisations 
(e.g. municipal recycling depots). At the end of their useful life, the devices may be 
returned to us for disposal.
WEEE reg. no. DE 39141253

Disposal

Control unit

Packaging

 

Wood, cardboard, plastics

 

Ä

When disposing of the product:

 

-

Ensure compliance with the relevant national disposal regulations and 
statutory requirements.

 

-

Ensure that any disposal company you use receives a list of the aforemen-
tioned materials along with the product.

 

-

Ensure that the materials are recycled or disposed of in an environmental-
ly friendly way.

Replacement parts

  CAUTION   Overall safety at risk

Failure to use original Mayser parts when replacing parts of the product can 
impair the function of the protective device.

 

Ä

Only use original Mayser parts.

Содержание 1006747
























Отзывы: