Maxon TE-250C Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 48

background image

1

1921 Slauson

A

ve. Santa Fe Springs, CA. 90670 (800) 227-41

16 F

AX (888) 771-7713

44

ADJUSTMENT

COVER

LIFTGATE WILL NOT LIFT RATED CAPACITY

3.

Check the 3250 PSI relief valve as

follows. With platform on the ground,
remove plug from hand pump port

(FIGS. 44-1 and 44-2)

. Install 0-4000

PSI pressure gauge in the hand pump
port

(FIGS. 44-1 and 44-2)

. Remove

cover for access to relief valve. Hold the
control switch in the “

RAISE

” position.

Adjust the relief valve until the gauge
reads 3250 PSI

(FIGS. 44-1 and 44-2)

.

Remove gauge and reinstall plug in the
port. Then, reinstall relief valve cover.

4.

Check if pump relief valve is dirty. Clean or

replace relief valve, if necessary.

1.

Use voltmeter to verify the battery voltage is 12.6

volts or more under load from pump motor.

2.

Check for structural damage or lack of lubrica-

tion. Replace worn parts.

TROUBLESHOOTING

ADJUSTMENT

COVER

HAND PUMP

PORT

Keep dirt, water and other contaminants
from entering the hydraulic system. Be-
fore opening the hydraulic fl uid reservoir
fi ller cap, drain plug and hydraulic lines,
clean up contaminants that can get in
the openings. Also, protect the openings
from accidental contamination during
maintenance.

CAUTION

ADJUSTING RAISING RELIEF VALVE

(GRAVITY DOWN POWER UNIT)

FIG. 44-1

ADJUSTING RAISING RELIEF VALVE

(POWER DOWN POWER UNIT)

FIG. 44-2

PRESSURE

GAUGE

RELIEF VALVE

ADJUST SCREW

HAND PUMP

PORT

RELIEF VALVE

ADJUST SCREW

PRESSURE

GAUGE

«
...
42
43
44
45
46
...
»

Содержание TE-250C

















































Отзывы:

Нет отзывов

Похожие инструкции для TE-250C

Бренд: National Instruments Страницы: 15

Бренд: National Instruments Страницы: 20

Бренд: National Instruments Страницы: 22

NI PXI-665 Series

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 30

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 34

Бренд: Paton Страницы: 31

Бренд: R-Tech Страницы: 57

Бренд: Truweld Equipment Страницы: 28

Бренд: TradeQuip Страницы: 9

Бренд: OMG Страницы: 16

Бренд: gala gar Страницы: 40

Бренд: STRIDE Страницы: 12

SR/ABITIGL ABITIG GRIP

Бренд: Abicor Binzel Страницы: 36

Бренд: DECA WELD Страницы: 56

Бренд: Neutec Страницы: 22

Бренд: CAME Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды