Matrix T3X-05 Скачать руководство пользователя страница 64

Страница: 64 / 78

10.3 aSSembly iNSTrUCTioNS - CoNTiNUed

CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide

A Open YELLOW AND WHITE HARDWARE BAGS.

B Assemble the contact HR crossbar to the left and right handlebars using

18-bUTToN Head SCreW

. Fasten

the contact HR crossbar/handlebar assembly to the console masts using

15-bUTToN Head SCreW aNd

12-flaT WaSHer

NOTE: Make sure the arrows on the mast rings are pointing upward towards the console when sliding into

place.

C Pull the HR wires through handlebars using wire pull. Pull mast wire through handlebar.

aSSembly TiP

: look at the labels on the HR

wire coming from the contact HR crossbar

to ensure contact with HR crossbar and

left-right handlebars are assembled in the proper orientation.

NOTE: Be careful not to pinch any wires while assembling the right console mast.

STeP 3

Содержание T3X-05















































































Результаты поиска

Содержание T3X-05

Отзывы:

Похожие инструкции для T3X-05

Бренды по названию

Популярные бренды

Matrix T3X-05, Руководство по обслуживанию

Результаты поиска

Содержание T3X-05

Отзывы:

Похожие инструкции для T3X-05

Бренды по названию

Популярные бренды