Matrix T3X-05 Скачать руководство пользователя страница 16

Страница: 16 / 78

1) To enter Engineering Mode, press & hold the INCLINE DOWN

and SPEED DOWN keys at the same time for 3-5 seconds until

Manager Mode appears on the display.

2) Press the INCLINE or SPEED keys until Engineering Mode

appears on the display (Figure A) and press ENTER.

3) To scroll between settings in the Engineering Mode, press the

INCLINE or SPEED keys.

4) Press ENTER to modify the settings once displayed.

5) Press any INCLINE or SPEED key to change the value of the

setting.

6) Press the PAUSE key to exit the setting without saving.

7) Once the setting is correct, press ENTER to save.

8) Press the EMERGENCY STOP to exit Engineering Mode..

6.1 USiNG eNGiNeeriNG mode

CUSTom SeTTiNG defaUlT miNimUm

maximUm

UNiT

deSCriPTioN

Disable Errors

OFF

N/A

Off - Shows Class A-C errors. On - Shows Class C errors only.

Elevation Minimum

239

N/A

Controls the low incline parameter.

Elevation Maximum 230

239

N/A

Controls the high incline parameter.

Auto Calibration

N/A

This function is to calibrate the treadmill incline.

Speed Units

MILE

KILOMETER

DISTANCE Measurement unit used for calorie calculations, distance, and

speed.

Pause Time

MINUTES

5 SECONDS

10 MINUTES SECOND /

MINUTE

Controls the maximum time the treadmill can be paused during

a workout.

Serial Number

Serial Number input is available for both the Console and

Frame. Due to the limited LED characters, 2 layers are used to

enter the serial number. First Layer:

- PPPPP V

- PPPPP is the product name

- V is the version. If the version is A, just leave this blank.

Second Layer

- YY MM nnnnn.

- YY is the year (11, 12).

- MM is the month (e.g. 08, 09, 10).

- nnnnn is the actual serial number.

Use the UP / DOWN LEVEL keys to navigate the layers and

the number keys to input the serial number. The product name

is dependent on the Machine Type setting.

For example, the console is TM523 with ver. A and the

manufactured date is 2012.10 with 98765. The frame is TM523

with ver. A and the manufactured date is 2012.11 with 32345.

Their serial numbers are:

Console SN: TM523 1rst layer, 121098765 2nd layer.

Frame SN: TM523 1rst layer, 121132345 2nd layer.

Reset Defaults

N/A

Reset the default values to factory settings.

Club ID

N/A

This sets the club ID for clubs using Asset Management.

Audio Source

OFF

TV / PCTV /

REMOTE TV

N/A

Sets which outside TV will have audio through the console

audio ports.

AM System

RF RADIO

N/A

To select AM output device by WIFI or RF Radio.

Volume Control

OFF

A. INPUT DEFAULT :15

B. MAX DEFAULT :32

C. OUTPUT DEFAULT :13

Controls the default TV volume for entertainment wired through

the C-Safe port.

a. Input Default (DF : 15 / Range : 1 ~ 15)

b. Max Default (DF : 32 / Range : 1 ~ 32)

c. Output Default (DF : 13 / Range : 1 ~ Max)

Remote TV support a / b / c item. TV and PCTV only support

c item.

Erp Time

OFF

0=OFF

MINUTE

Belt Stop function for user’s existence detect.

6.2 eNGiNeeriNG mode oVerVieW

fiGUre a

CHaPTer 6: eNGiNeeriNG mode

Содержание T3X-05















































































Результаты поиска

Содержание T3X-05

Отзывы:

Похожие инструкции для T3X-05

Бренды по названию

Популярные бренды

Matrix T3X-05, Руководство по обслуживанию

Результаты поиска

Содержание T3X-05

Отзывы:

Похожие инструкции для T3X-05

Бренды по названию

Популярные бренды